30 hp motor soft starter, 22 kW three phase 240v, 415v, 480v, 690v AC motor starter for choice.
| Model | GS2-022 (220v, 240v), GS3-022 (380v, 400v, 415v), GS4-022 (460v, 480v), GS6-022 (575v, 690v). | ||
| Capacity | 30 hp (22 kw) | ||
| Current | 43 amps at 380v/480v, 90 amps at 220v, 30 amps at 690v | ||
| Weight | 5 kgs | ||
| Dimension | 270*146*160 mm | ||
| Input | Voltage | Three-phase 220v, 440v, 480v, 690v AC | |
| Frequency | 50Hz/ 60Hz | ||
| Adaptive Motor | Squirrel-cage three-phase asynchronous motor | ||
| Starting Times | It is recommended not to exceed 20 times per hour. | ||
| 485 Communication | DB9 interface, male plug, ① is RS485+, ⑥ is RS485- | ||
| Control Mode |
| ||
| Start Mode |
| ||
| Stop Mode |
| ||
| Protective Function |
| ||
| Ambient | Place to be used | Indoor location with good ventilation free from corrosive gas and conductive dust. | |
| Altitude | Below 1000M. It has to increase the soft starter rate power when the altitude is more than 1000M. | ||
| Temperature | -30 +55 oC | ||
| Humidity | 90%RH without dew condensation. | ||
| Vibration | <0.5G | ||
| Structure | Enclosure | IP 20 | |
| Cooling | Natural wind cooling. | ||
Details

Tips: The difference between soft starter and variable frequency drive (VFD)
From the application, the soft starter and variable frequency drive (VFD) are two completely different products. The soft starter is actually a device that controls the voltage and limits the starting current, uses for starting motor and only changes the output voltage amplitude without changing the frequency. And VFD is used for the device needed speed governing, the output not only changes the voltage but also changes the frequency. From the function, VFD has all the functions of the soft starter, so it can be said that VFD is a more powerful soft starter.
Although the soft starter solves the problem of motor starting, but there is no significant energy saving effect. When start using energy-saving operation mode, no-load energy saving is 40%, and load energy saving is only 5%. VFD not only solves the big impact current caused by the motor starting, but also has the good energy saving effect and the frequency conversion ability.
2. what certificate of your soft starter device do you have? please list all of them and send to me.
Thanks!
Vivian
I gave you a picture of the name plate attached – what is the rated current?
How do I set it? I assume I do this before I provide power to the motor?
When I hit stop/reset and then run, the motor starts to turn for ½ second and then stops. The message I get is error 04 – input lost. See attached photos. I do not know what is wrong?
The motor will run for 10 to 15 seconds and then shut down with no error codes. The motor is a 15 HP, 3ph, 460v 20.5 FLA. I have changed the parameter FP to 22.
I also noticed that when I start the motor up, the AMP spike into the 60 – 70 range. And on the voltage screen, I see 502 to 515 when I measured voltage. I had L1 – L2 470, L2 – L3 470.6, L1 – L3 470.6. I would like phone support when I'm on-site if possible my number is (951)212-6926.
It immediately overloaded the generator and the generator turned off.
I had set FB=1 and FP=30. Did you all install the device to make this work with 240 volts?