Digital Counter, 6 Digit, Up/Down, Number/Length/Batch

$89.14
6 digit counter can be used for counting number/length/batch, position control of balers controlled by variable frequency motor, and measuring height, position and angle. Digital counter with up/down input modes can preset count value or length, and simultaneously display the total count, counting length and batch value in real time.
SKU: ATO-DIGC-FH6D
*
*
*
*
*
*
*
*
Free Shipping
Delivery date: 6-12 days

Digital counter has 6 digit display, 4 kinds of up/down input modes, DC 12V/24V external power supply.

Features:

  • Digital counter accuracy: 0.01%, minimum resolution: 0.0001.
  • Input/output signals photoelectric isolated, anti-interference ability.
  • Input: 4 kinds of input modes, a variety of input signals, various waveform pulse, grating, proximity sensors, photoelectric sensors, contact switches, encoders, etc. (NPN, PNP).
  • Output: 8 kinds of output modes to select, up to 3 segments control output, suitable for various control requirements.
  • 6 digit display, has external power supply DC 12V/24V/30mA especially for sensor.
  • Standard RS232 or RS485 MODBUS RTU communication, can be directly connected with computers, PLC or other equipments.

Specification:

ModeATO-DIGC-FH8/FH7
Weight300g
Accuracy0.01%
Power supplyAC 90-260V, or AC/DC 12-30V/DC 24V, power dissipation≤5VA
Input signalPulse signal, square wave, sine wave, 5V≤H≤30V, 0≤L≤2V, rising edge trigger, frequency: 0.01~9KHz (square wave)
Counting rate≤5000 CPS (switching input, software selectable), ≤2000Hz (encoder input)
Display counting range-199999~999999
Ratio setting range0.00001~99999.9
Input impedance≥10KΩ
Relay output methodR, N, C, F, H, L (count), upper and lower limits alarm, capacity AC 250V/3A, DC 30V/3A COSΦ=1
Transmission output4-20mA, 0-10V, etc. (range can be set)
Insulation resistance≥100MΩ (between DC 500V power terminal and external terminal)
Dielectric strengthAC 1500V 1min (between power terminal and external terminal)
EnvironmentAmbient temperature: 0~50°C, relative humidity: 35~85%RH
External power supplyDC 12V±5%, 50mA max / DC 24V±5%, 30mA max
Protection classIP65

Selection table:

Dimension (W*H*L)Power supplyFunctionAL1AL2Communication interfaceExternal power supplyInput signal
7: 72*72*80mm with hole size 67.5*67.5mm;
8: 96*48*80mm with hole size 92*45mm
V0: AC 90-260V;
VE: AC/DC 12-30V, or DC 24V
C: Number/length;
B: Batch;
P: Position control
N: No output;
R: Relay;
S: SSR/LOGIC
N: No output;
R: Relay;
S: SSR/LOGIC
C0: No communication;
C2: RS232;
C4: RS485
A: DC 12V/30mA;
B: DC 24V/30mA;
C: DC 5V
I0: Two pulse inputs (encoder);
I1: INA (one input for switching input)

Digital counter up/down input modes:
Mode A: Up (addition)
INA counts up. INB is GATE function. When INB is high level (or shorted with +12V), INA input is forbidden.
Digital counter up down mode a
Mode B: Up/down (addition or subtraction)
INA counts up. INB is count-down control function. When INB is high level, INA turns count-up into count-down.
Digital counter up down mode b
Mode C: Up/down (addition and subtraction)
INA counts up, INB counts down.
Digital counter up down mode c
Mode D: Up/down (for encoder)
INA signal leads INB signal (count-up). INA signal lags INB signal (count-down). It is often used for encoder or grating input.
Digital counter up down mode d
Wiring diagram:
Digital counter up down wiring diagram
Tips: Digital counter application in positioning and speed regulation of elevator
The leveling signal of elevator is obtained by the position sensors installed in the elevator well. When there are many floors, the number of such signals is large, and there are certain difficulties in equipment installation and maintenance. At the same time these signals take up a lot of PLC input port. If using PLC and high-speed counter for positioning, it can not only solve these problems, but also can achieve frequency control of elevator.
When the elevator is running, digital counter completes the counting work driven by the optical encoder. When the elevator car rises, digital counter counts up. When the elevator car goes down, digital counter counts down. The current value of the counter is the exact position of the car in the elevator well. In this way, the accurate positioning of the elevator is realized. This positioning method has the following functions: It realizes the floor digital display of the elevator lobby and car, determines the running direction, and determines the braking time of leveling.

In this video, ATO will show you how to wire a digital counter. And how to set the basic parameters of digital counter.

Digital Counter and Proximity Sensor Counting

In this video, we show you how to utilize ATO's 6-digit counter meter with a proximity sensor for accurate counting. We have covered all the basic steps, guiding you through the wiring, setup, configuration, and functionality of the meter. By following the steps demonstrated in this video, you can leverage the power of this digital counter to accurately track your industrial processes.

Product reviews
Digital counter for calculating cloth length
5
Dylan
Avatar
9/26/2018 2:34 AM
We use the digital counter with 6 digit to calculate the length of the cloth. We have a lot of questions in the process of installation and debugging, and the customer service staff answers us carefully. Now the digital counter works well. The length calculated by the digital counter is very accurate.
Was this review helpful? Yes No (0/0)
Very accurate
5
Schuster
Avatar
10/12/2018 7:41 AM
The up/down digital counter has good quality and high accuracy. It is very simple to operate and easy to install. We have used it for a long time, the counting function is still very accurate. We are also satisfied with fast delivery and tight packaging.
Was this review helpful? Yes No (0/0)
Digital counter measure number of motor rotations
5
Bryan
Avatar
4/9/2020 12:36 AM
Can we connect your digital counter to proximity sensor so that they can measure the number of motor rotations?
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, you can choose the digital counter with the Function C (number/length) to count numbers. We recommend that you use a photoelectric sensor or a rotary encoder to measure high-speed rotating motors. If you want to measure the rotational speed of the motor, we suggest you choosing another model ATO-DIGC-FA6D Frequency/Rev/Speed Digital Counter.
Does your digital counter have a multiplication function?
5
Lieder
Avatar
11/25/2021 8:37 PM
We would like to integrate your ATO-DIGC-FH6D digital counter with a photoelectric sensor as a detection gauge. The sensor will be triggered when the strip is pass-by and send signal to the counter. In order to count the correct quantity, we need to multiply the number as every strip has 20 units of component. I would like to know if the counter has any features of multiple functions.
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, our counter has the multiply function you mentioned below, and the coefficient can be set in the counter parameter setting.
Problem of BT/Up button
5
rik
Avatar
3/1/2023 1:19 AM
We received the digital counter today. So far the front label was not applied fully. We tried to push it down, but the BT or Up button does not click.
The other three buttons, SET RST and down click fine, but BT/Up button cannot be pushed. So we have a defective counter and a rotary encoder with the wrong cable length. How would you like to proceed?
Was this review helpful? Yes No (0/0)
ATO Responded
If the BT/Up button of your counter cannot be used, you can try to connect to 220V AC power first, and then check whether each button can be used (please refer to the manual to try to use these buttons to modify parameters).
Of course, if the BT/Up button is indeed unable to be pressed, can you please set the parameters and provide a video to show this problem to us for further confirmation. Please confirm to us whether the counter has quality problems, so that we can proceed to the next step. You can send us the large video file via wetransfer.com.
Can digital counter read in metric or numeric?
5
skyla
Avatar
3/1/2023 8:25 PM
Awesome can this read in metric or numeric?
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, you can modify the PC coefficient menu according to the metric or numeric display you want the counter to display.
Can plug in a position transducer/linear scale and set the alarms to go off at a set distance?
5
Shelton
Avatar
3/27/2023 7:26 PM
Can plug in a position transducer/linear scale and set the alarms to go off at a set distance?
Was this review helpful? Yes No (0/0)
ATO Responded
We can plug in a position transducer/linear scale and set alarm according to your requirement. If it is a position resistance scale, it cannot be used. By position transducer do you mean an encoder or a wheel sensor? Or some other position sensor?
Regarding the digital counter
5
Vicona
Avatar
8/20/2025 12:45 AM
Can this digital counter operate from a 24V DC power supply? Can the input be used with an external relay for counting? I will be using a 24V DC signal for counting.
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, this counter can operate from a 24V DC power supply and can also use an external relay for counting. Simply set Inp = A.
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

Digital counter has 6 digit display, 4 kinds of up/down input modes, DC 12V/24V external power supply.

Features:

  • Digital counter accuracy: 0.01%, minimum resolution: 0.0001.
  • Input/output signals photoelectric isolated, anti-interference ability.
  • Input: 4 kinds of input modes, a variety of input signals, various waveform pulse, grating, proximity sensors, photoelectric sensors, contact switches, encoders, etc. (NPN, PNP).
  • Output: 8 kinds of output modes to select, up to 3 segments control output, suitable for various control requirements.
  • 6 digit display, has external power supply DC 12V/24V/30mA especially for sensor.
  • Standard RS232 or RS485 MODBUS RTU communication, can be directly connected with computers, PLC or other equipments.

Specification:

ModeATO-DIGC-FH8/FH7
Weight300g
Accuracy0.01%
Power supplyAC 90-260V, or AC/DC 12-30V/DC 24V, power dissipation≤5VA
Input signalPulse signal, square wave, sine wave, 5V≤H≤30V, 0≤L≤2V, rising edge trigger, frequency: 0.01~9KHz (square wave)
Counting rate≤5000 CPS (switching input, software selectable), ≤2000Hz (encoder input)
Display counting range-199999~999999
Ratio setting range0.00001~99999.9
Input impedance≥10KΩ
Relay output methodR, N, C, F, H, L (count), upper and lower limits alarm, capacity AC 250V/3A, DC 30V/3A COSΦ=1
Transmission output4-20mA, 0-10V, etc. (range can be set)
Insulation resistance≥100MΩ (between DC 500V power terminal and external terminal)
Dielectric strengthAC 1500V 1min (between power terminal and external terminal)
EnvironmentAmbient temperature: 0~50°C, relative humidity: 35~85%RH
External power supplyDC 12V±5%, 50mA max / DC 24V±5%, 30mA max
Protection classIP65

Selection table:

Dimension (W*H*L)Power supplyFunctionAL1AL2Communication interfaceExternal power supplyInput signal
7: 72*72*80mm with hole size 67.5*67.5mm;
8: 96*48*80mm with hole size 92*45mm
V0: AC 90-260V;
VE: AC/DC 12-30V, or DC 24V
C: Number/length;
B: Batch;
P: Position control
N: No output;
R: Relay;
S: SSR/LOGIC
N: No output;
R: Relay;
S: SSR/LOGIC
C0: No communication;
C2: RS232;
C4: RS485
A: DC 12V/30mA;
B: DC 24V/30mA;
C: DC 5V
I0: Two pulse inputs (encoder);
I1: INA (one input for switching input)

Digital counter up/down input modes:
Mode A: Up (addition)
INA counts up. INB is GATE function. When INB is high level (or shorted with +12V), INA input is forbidden.
Digital counter up down mode a
Mode B: Up/down (addition or subtraction)
INA counts up. INB is count-down control function. When INB is high level, INA turns count-up into count-down.
Digital counter up down mode b
Mode C: Up/down (addition and subtraction)
INA counts up, INB counts down.
Digital counter up down mode c
Mode D: Up/down (for encoder)
INA signal leads INB signal (count-up). INA signal lags INB signal (count-down). It is often used for encoder or grating input.
Digital counter up down mode d
Wiring diagram:
Digital counter up down wiring diagram
Tips: Digital counter application in positioning and speed regulation of elevator
The leveling signal of elevator is obtained by the position sensors installed in the elevator well. When there are many floors, the number of such signals is large, and there are certain difficulties in equipment installation and maintenance. At the same time these signals take up a lot of PLC input port. If using PLC and high-speed counter for positioning, it can not only solve these problems, but also can achieve frequency control of elevator.
When the elevator is running, digital counter completes the counting work driven by the optical encoder. When the elevator car rises, digital counter counts up. When the elevator car goes down, digital counter counts down. The current value of the counter is the exact position of the car in the elevator well. In this way, the accurate positioning of the elevator is realized. This positioning method has the following functions: It realizes the floor digital display of the elevator lobby and car, determines the running direction, and determines the braking time of leveling.

Product reviews
Digital counter for calculating cloth length
5
Dylan
Avatar
9/26/2018 2:34 AM
We use the digital counter with 6 digit to calculate the length of the cloth. We have a lot of questions in the process of installation and debugging, and the customer service staff answers us carefully. Now the digital counter works well. The length calculated by the digital counter is very accurate.
Was this review helpful? Yes No (0/0)
Very accurate
5
Schuster
Avatar
10/12/2018 7:41 AM
The up/down digital counter has good quality and high accuracy. It is very simple to operate and easy to install. We have used it for a long time, the counting function is still very accurate. We are also satisfied with fast delivery and tight packaging.
Was this review helpful? Yes No (0/0)
Digital counter measure number of motor rotations
5
Bryan
Avatar
4/9/2020 12:36 AM
Can we connect your digital counter to proximity sensor so that they can measure the number of motor rotations?
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, you can choose the digital counter with the Function C (number/length) to count numbers. We recommend that you use a photoelectric sensor or a rotary encoder to measure high-speed rotating motors. If you want to measure the rotational speed of the motor, we suggest you choosing another model ATO-DIGC-FA6D Frequency/Rev/Speed Digital Counter.
Does your digital counter have a multiplication function?
5
Lieder
Avatar
11/25/2021 8:37 PM
We would like to integrate your ATO-DIGC-FH6D digital counter with a photoelectric sensor as a detection gauge. The sensor will be triggered when the strip is pass-by and send signal to the counter. In order to count the correct quantity, we need to multiply the number as every strip has 20 units of component. I would like to know if the counter has any features of multiple functions.
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, our counter has the multiply function you mentioned below, and the coefficient can be set in the counter parameter setting.
Problem of BT/Up button
5
rik
Avatar
3/1/2023 1:19 AM
We received the digital counter today. So far the front label was not applied fully. We tried to push it down, but the BT or Up button does not click.
The other three buttons, SET RST and down click fine, but BT/Up button cannot be pushed. So we have a defective counter and a rotary encoder with the wrong cable length. How would you like to proceed?
Was this review helpful? Yes No (0/0)
ATO Responded
If the BT/Up button of your counter cannot be used, you can try to connect to 220V AC power first, and then check whether each button can be used (please refer to the manual to try to use these buttons to modify parameters).
Of course, if the BT/Up button is indeed unable to be pressed, can you please set the parameters and provide a video to show this problem to us for further confirmation. Please confirm to us whether the counter has quality problems, so that we can proceed to the next step. You can send us the large video file via wetransfer.com.
Can digital counter read in metric or numeric?
5
skyla
Avatar
3/1/2023 8:25 PM
Awesome can this read in metric or numeric?
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, you can modify the PC coefficient menu according to the metric or numeric display you want the counter to display.
Can plug in a position transducer/linear scale and set the alarms to go off at a set distance?
5
Shelton
Avatar
3/27/2023 7:26 PM
Can plug in a position transducer/linear scale and set the alarms to go off at a set distance?
Was this review helpful? Yes No (0/0)
ATO Responded
We can plug in a position transducer/linear scale and set alarm according to your requirement. If it is a position resistance scale, it cannot be used. By position transducer do you mean an encoder or a wheel sensor? Or some other position sensor?
Regarding the digital counter
5
Vicona
Avatar
8/20/2025 12:45 AM
Can this digital counter operate from a 24V DC power supply? Can the input be used with an external relay for counting? I will be using a 24V DC signal for counting.
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, this counter can operate from a 24V DC power supply and can also use an external relay for counting. Simply set Inp = A.
Only registered users can write reviews
Customers who bought this item also bought

Slot Type Photoelectric Sensor

ATO-PHOS-ST
$63.81
Slot-type photoelectric sensor is also known as U-type photoelectric sensor. It's a type of through beam photoelectric sensor and easier to align through beam. Slot type photoelectric sensor can distinguish opaque objects, with power supply DC 12V-24V (6-36V), small installation space, reverse power protection.

Retro-reflective Photoelectric Sensor

ATO-PHOS-RR
$60.22
Retro-reflective photoelectric sensor consists of light projector and light receiver in one, has long effective distance range with the help of reflective board. The supply voltage is DC 12V-24V (6-36V) or AC 110V-220V (90-250V). Infrared photoelectric sensor can distinguish the opaque reflective object, with less susceptible to interference, fast reaction, long life, high resolution and high reliability.

Through Beam Photoelectric Sensor

ATO-PHOS-TB
$41.36
Through beam photoelectric sensor consists of a light projector and a light receiver, both of which are separated in structure. The supply voltage is DC 12V-24V or AC 110V-220V. Infrared photoelectric sensor can distinguish the opaque reflective object, with long effective detection distance 5/15/50m, less susceptible to interference, long life, and high reliability.

Diffuse Reflective Photoelectric Sensor

ATO-PHOS-DR
$59.27
Diffuse reflective photoelectric sensor consists of light projector and light receiver in one, can distinguish transparent or opaque reflective object. The supply voltage is DC 12V-24V (6-36V) or AC 110V-220V (90-250V). Infrared photoelectric sensor can be compensated for longer distance with sensitivity controller, less susceptible to interference, fast reaction, long life, high resolution and high reliability.

Strain Gauge Load Cell, S type, 5kg/50kg/1000kg/3 ton to 20 ton

ATO-LC-S01
$88.41
S type load cell can bear both tension and pressure, with good output symmetry, high accuracy, compact structure and complete specifications. Strain gauge load cell can be applied for batching scale, electronic-mechanical scale, crane scales and other force value measurement and control.