Digital counter has 8 digit display, 4 kinds of up/down input modes, DC 12V/24V external power supply.
Features:
- Digital counter accuracy: 0.01%, minimum resolution: 0.0001.
- Input/output signals photoelectric isolated, anti-interference ability.
- Input: 4 kinds of input modes, a variety of input signals, various waveform pulse, grating, proximity sensors, photoelectric sensors, contact switches, encoders, etc. (NPN, PNP).
- Output: 8 kinds of output modes to select, up to 3 segments control output, suitable for various control requirements.
- 8 digit display, has external power supply DC 12V/24V/30mA especially for sensor.
- Standard RS232 or RS485 MODBUS RTU communication, can be directly connected with computers, PLC or other equipments.
Specification:
| Mode | ATO-DIGC-FH8 |
| Weight | 400g |
| Accuracy | 0.01% |
| Power supply | AC 90-260V, or AC/DC 12-30V/DC 24V, power dissipation≤5VA |
| Input signal | Pulse signal, square wave, sine wave, 5V≤H≤30V, 0≤L≤2V, rising edge trigger, frequency: 0.01~9KHz (square wave) |
| Counting rate | ≤5000 CPS (switching input, software selectable), ≤2000Hz (encoder input) |
| Display counting range | -19999999~99999999 |
| Ratio setting range | 0.0000001~9999999.9 |
| Input impedance | ≥10KΩ |
| Relay output method | R, N, C, F, H, L (count), upper and lower limits alarm, capacity AC 250V/3A, DC 30V/3A COSΦ=1 |
| Transmission output | 4-20mA, 0-10V, etc. (range can be set) |
| Insulation resistance | ≥100MΩ (between DC 500V power terminal and external terminal) |
| Dielectric strength | AC 1500V 1min (between power terminal and external terminal) |
| Environment | Ambient temperature: 0~50°C, relative humidity: 35~85%RH |
| External power supply | DC 12V±5%, 50mA max / DC 24V±5%, 30mA max |
| Protection class | IP65 |
Selection table:
| Dimension (length*height*depth) | Power supply | Function | AL1 | AL2 | Communication interface | External power supply | Input signal |
| 8: 96*48*80mm with hole size 92*45mm | V0: AC 90-260V; VE: AC/DC 12-30V, or DC 24V | C: Number/length; B: Batch; P: Position control | N: No output; R: Relay; S: SSR/LOGIC | N: No output; R: Relay; S: SSR/LOGIC | C0: No communication; C2: RS232; C4: RS485 | A: DC 12V/30mA; B: DC 24V/30mA; | I0: Two pulse inputs (encoder); I1: INA (one input for switching input) |
Digital counter up/down input modes:
Mode A: Up (addition)
INA counts up. INB is GATE function. When INB is high level (or shorted with +12V), INA input is forbidden.
Mode B: Up/down (addition or subtraction)
INA counts up. INB is count-down control function. When INB is high level, INA turns count-up into count-down.
Mode C: Up/down (addition and subtraction)
INA counts up, INB counts down.
Mode D: Up/down (for encoder)
INA signal leads INB signal (count-up). INA signal lags INB signal (count-down). It is often used for encoder or grating input.
Wiring diagram:
Tips: Components of digital counter
- A, B input channels
The function of the input channel is amplifying and shaping the measured signal to a standard pulse signal. - Door
The gate is a comparison circuit used for quantizing. It can control whether the counting pulse signal can input digital counter. - Counting and display unit
The counting and display circuit is used to count the pulse signal from the main gate and display the result of the counting as a digital form. For easy reading, digital counter usually uses a decimal counting circuit. - Time base unit
The time base circuit is mainly composed of a crystal oscillator, a frequency divider, and a frequency multiplier. The time base circuit is mainly used to generate various standard time signals. The timing signal can be single or multinomial. - Control unit
The function of the control circuit is to generate three control signals of gating signal, registering signal and zero resetting signal. So that various circuit units of digital counter can automatically measure in an orderly process according to the sequence of preparation, measurement and display.
Product reviews
Use of 8 digit digital counter
Anshul
4/12/2021 9:11 PM
Can we connect you digital counter to proximity sensor, so can mesure motor number of revolution?
Was this review helpful? (0/0)
My question about 8-digit digital counter
Felicia
5/27/2021 12:32 AM
I have some inquiries about your 8 digit digital counter: Here are a couple of question.
1. Say if I set my counter to 10million count and it reached a value of 5 million and there was a power outage or someone shuts of the power at 5million count. So when the power is turned back on, will it hold its value and start counting from 5 million count or will become zero.
2. Do I have to use only the proximity switch that you suggested or I can use any 24VDC PNP proximity switch to it.
3. It will trigger a relay output when the preset value is reached of 10million counts.
4. External reset can be used when it reaches is preset value.
5. If this is the right fit, I will need four of these. What would be the lead time.
1. Say if I set my counter to 10million count and it reached a value of 5 million and there was a power outage or someone shuts of the power at 5million count. So when the power is turned back on, will it hold its value and start counting from 5 million count or will become zero.
2. Do I have to use only the proximity switch that you suggested or I can use any 24VDC PNP proximity switch to it.
3. It will trigger a relay output when the preset value is reached of 10million counts.
4. External reset can be used when it reaches is preset value.
5. If this is the right fit, I will need four of these. What would be the lead time.
Was this review helpful? (0/0)
Can I use the 8-digit digital counter with the PNP NO output signal of the proximity sensor?
Murky
11/25/2021 1:32 AM
We are using a PNP NO output signal proximity sensor (to count the values, maximum counting rate up to 200rpm). Can I use your 8 digit counter with a PNP NO output signal of proximity sensor?
Was this review helpful? (0/0)
Can use the buzzer alert if quantity achieve ?
Mohd Azieka
6/12/2023 10:56 PM
I have some inquiries about your 8 digit digital counter: Here are a couple of question.
1. This digital counter can connect with buzzer and limit sensor for output?
2. If quantity achieve 5 millions it will trigger to buzzer that we install
3. Please email me if not understand the question
Email me i can give picture of idea from our side
1. This digital counter can connect with buzzer and limit sensor for output?
2. If quantity achieve 5 millions it will trigger to buzzer that we install
3. Please email me if not understand the question
Email me i can give picture of idea from our side
Was this review helpful? (0/0)
8 Digit, Up/Down
Moayad
8/19/2026 1:01 AM
high speed input External Power Supply .. very helpfull
Was this review helpful? (0/0)
Only registered users can write reviews
Customers who bought this item also bought
Slot Type Photoelectric Sensor
ATO-PHOS-ST
$63.81
Slot-type photoelectric sensor is also known as U-type photoelectric sensor. It's a type of through beam photoelectric sensor and easier to align through beam. Slot type photoelectric sensor can distinguish opaque objects, with power supply DC 12V-24V (6-36V), small installation space, reverse power protection.