Hydraulic Orbital Motor, 160cc/rev

$321.89
Buy hydraulic orbital motor online, low speed high torque with 160cc/r displacement. It is a spool valve motor can be used in parallel or series, selectable flat key shaft or splined shaft, mounting flanges of 2 bolts and 4 bolts.
SKU: ATO-HOM-160
*
*
Free Shipping
Delivery date: 6-12 days

Hydraulic orbital motor is designed for disc distribution flow, which can provide improved performance at low speed and higher volumetric for the automatically compensated wear. It can be used on heavy vehicles and machinery in traction drive applications.

Specification

ModelATO-OMP-160
Shaft Type (Optional)Flat Key, Splined
Flange Type (Optional)2 Bolts, 4 Bolts
Displacement160 cc/rev (160 cm3/rev)
Working Pressure15 MPa
FlowContinuous57 LPM
Intermittent68 LPM
Max.SpeedContinuous354 rpm
Intermittent425 rpm
PressureContinuous115 ∆Bar
Intermittent124 ∆Bar
TorqueContinuous228 Nm
Intermittent261 Nm
Weight7.5kg

Note:

  • A simultaneous maximum torque and maximum speed are not recommended.
  • ∆Bar refers to true pressure difference between inlet port and outlet port.
  • Continuous Rating means that the motor may be run continuously at these ratings.
  • Intermittent operation refers to that the motor running time must not exceed 10% per minute under this condition.

*To assure the best orbital motor life, run it for approximately one hour at 30% of rated pressure before application to full load. Be sure this motor is filled with fluid before any load applications.

Dimensions (Unit: mm)

Dimensions of hydraulic orbital motor

L1=160mm

Hydraulic Orbital Motor Shaft (Unit: mm)

motor shafts of hydraulic orbital motor

Flange Types (Unit: mm)

2 bolt flange hydraulic orbital motor

4 bolt flange hydraulic orbital motor

L=167mm

Details

Hydraulic Orbital Motor Details

Tips for using hydraulic orbital motor

  • Before operation, check whether all components of the hydraulic system are connected correctly, and add oil to the specified height through the filter.
  • Start and run this hydraulic orbital motor for 10 to 15 minutes under no load, and exhaust, foam in the fuel tank, noise in the system, and stagnation in the motor cylinder all prove that there is air in the system.
  • After removing the air, fill up the fuel tank, and then gradually increase the load on the motor until the maximum load, and observe whether there are abnormal phenomena such as noise, oil rise and oil leakage.
  • Replace the oil once after 50 hours of operation, and then follow the maintenance rules.
  • If it is not a motor failure, please do not disassemble it.
Product reviews
Stable and reliable
5
Jake
Avatar
4/13/2026 7:16 PM
This motor delivers strong low-speed torque for heavy machinery. Stable pressure, smooth operation, flexible mounting, and performs reliably in continuous heavy-duty work.
Was this review helpful? Yes No (0/0)
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

Hydraulic orbital motor is designed for disc distribution flow, which can provide improved performance at low speed and higher volumetric for the automatically compensated wear. It can be used on heavy vehicles and machinery in traction drive applications.

Specification

ModelATO-OMP-160
Shaft Type (Optional)Flat Key, Splined
Flange Type (Optional)2 Bolts, 4 Bolts
Displacement160 cc/rev (160 cm3/rev)
Working Pressure15 MPa
FlowContinuous57 LPM
Intermittent68 LPM
Max.SpeedContinuous354 rpm
Intermittent425 rpm
PressureContinuous115 ∆Bar
Intermittent124 ∆Bar
TorqueContinuous228 Nm
Intermittent261 Nm
Weight7.5kg

Note:

  • A simultaneous maximum torque and maximum speed are not recommended.
  • ∆Bar refers to true pressure difference between inlet port and outlet port.
  • Continuous Rating means that the motor may be run continuously at these ratings.
  • Intermittent operation refers to that the motor running time must not exceed 10% per minute under this condition.

*To assure the best orbital motor life, run it for approximately one hour at 30% of rated pressure before application to full load. Be sure this motor is filled with fluid before any load applications.

Dimensions (Unit: mm)

Dimensions of hydraulic orbital motor

L1=160mm

Hydraulic Orbital Motor Shaft (Unit: mm)

motor shafts of hydraulic orbital motor

Flange Types (Unit: mm)

2 bolt flange hydraulic orbital motor

4 bolt flange hydraulic orbital motor

L=167mm

Details

Hydraulic Orbital Motor Details

Tips for using hydraulic orbital motor

  • Before operation, check whether all components of the hydraulic system are connected correctly, and add oil to the specified height through the filter.
  • Start and run this hydraulic orbital motor for 10 to 15 minutes under no load, and exhaust, foam in the fuel tank, noise in the system, and stagnation in the motor cylinder all prove that there is air in the system.
  • After removing the air, fill up the fuel tank, and then gradually increase the load on the motor until the maximum load, and observe whether there are abnormal phenomena such as noise, oil rise and oil leakage.
  • Replace the oil once after 50 hours of operation, and then follow the maintenance rules.
  • If it is not a motor failure, please do not disassemble it.
Product reviews
Stable and reliable
5
Jake
Avatar
4/13/2026 7:16 PM
This motor delivers strong low-speed torque for heavy machinery. Stable pressure, smooth operation, flexible mounting, and performs reliably in continuous heavy-duty work.
Was this review helpful? Yes No (0/0)
Only registered users can write reviews
Customers who bought this item also bought

Hydraulic Orbital Motor, 200cc/rev

ATO-HOM-200
$322.89
Low speed high torque hydraulic orbital motor at affordable price. It is a spool valve motor with 200cc/r displacement, reliable operation and high efficiency, selectable flat key shaft or splined shaft, and mounting flanges of 2 bolts and 4 bolts. This orbit motor can be used in parallel or in series.

Hydraulic Orbital Motor, 250cc/rev

ATO-HOM-250
$324.59
Factory price hydraulic orbital motor with high performance shaft, can bear high pressure, high speed and high radial force. Mounting flanges of 2 bolts and 4 bolts, easy to install. 250cc/r displacement, max. speed up to 281 rpm, torque up to 378Nm, can be used in parallel or series.