Hydraulic Orbital Motor, 50cc/rev

$316.89
High peformance hydraulic orbital motor online sale, it is widely applied in agriculture machinery, fishing machinery, plastic industry, and construction machinery, etc. It can be used in parallel or series with 50 cc/rev displacement and flat key shaft or splined shaft. Mounting flanges of 2 bolts and 4 bolts are available.
SKU: ATO-HOM-50
*
*
Free Shipping
Delivery date: 6-12 days

High torque low speed orbital hydraulic motor is widely applied in agriculture machinery, fishing machinery, plastic industry, mining, and construction machinery, especially fitted to lower load applications, such as plastic injection mold machines, cleaners, grass cutters, winches, conveyors, slews, sweeper drives, augers, cutters, mowers and chippers.

Specification

ModelATO-OMP-50
Shaft Type (Optional)Flat Key, Splined
Flange Type (Optional)2 Bolts, 4 Bolts
Displacement50cc/rev (50cm3/rev)
Working Pressure15 MPa
FlowContinuous38LPM
Intermittent45LPM
Max.SpeedContinuous698rpm
Intermittent859rpm
PressureContinuous124∆Bar
Intermittent138∆Bar
TorqueContinuous73Nm
Intermittent84Nm
Weight6.5kg

Note:

  • A simultaneous maximum torque and maximum speed are not recommended.
  • ∆Bar refers to true pressure difference between inlet port and outlet port.
  • Continuous Rating means that the motor may be run continuously at these ratings.
  • Intermittent operation refers to that the motor running time must not exceed 10% per minute under this condition.

*To assure the best orbital motor life, run it for approximately one hour at 30% of rated pressure before application to full load. Be sure this motor is filled with fluid before any load applications.

Dimensions (Unit: mm)

Dimensions of hydraulic orbital motor

L1=140mm

Hydraulic Orbital Motor Shaft (Unit: mm)

motor shafts of hydraulic orbital motor

Flange Types (Unit: mm)

2 bolt flange hydraulic orbital motor

4 bolt flange hydraulic orbital motor

L=147mm

Details

Hydraulic Orbital Motor Details

Tips: Reasons for bubbles in hydraulic orbital motor

When the hydraulic orbital motor is being transported, a small amount of gas will be suspended in the gear oil as a spherical bubble with a small diameter during filling. Gas and gear oil melt into each other and will not change the physical properties of gear oil, but when gear oil melts some amount of gas and becomes saturated, it melts because of a sudden drop in pressure when it flows through the overflow valve or the inlet of the pump. A part of the saturated gas in the gear oil will be separated out and slowly gathered together, resulting in large bubbles.

Suppose the oil level in the hydraulic orbital motor's hydraulic oil tank is too low. In that case, the returned gear oil will appear on the surface of the oil tank and cause a lot of bubbles, and if the oil inlet pipe and the inlet of the hydraulic pump leak, there will be a lot of bubbles. The gas enters the hydraulic circulation system and bubbles appear.

VFD Two-Wire Control Wiring with Push Button for Forward Motor

In this video we've guided you through how to do VFD control wiring with a self-lock push button switch to run the motor in forward direction. We've covered everything from wiring to programming and even a test run. So just watch it through and hope you'll find it informative and helpful.

Product reviews
Works pretty good
5
Matt
Avatar
3/23/2022 9:30 PM
Works great in our crane, the service is good. Seller gave us professional technical support. If we need more, we will contact you.
Was this review helpful? Yes No (0/0)
This hydraulic orbital motor runs smoothly
5
Kirk
Avatar
7/1/2026 7:05 PM
Very good hydraulic motor for industrial use. It runs smoothly in both continuous and intermittent conditions, and the torque output is strong enough for our mining equipment setup.
Was this review helpful? Yes No (0/0)
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

High torque low speed orbital hydraulic motor is widely applied in agriculture machinery, fishing machinery, plastic industry, mining, and construction machinery, especially fitted to lower load applications, such as plastic injection mold machines, cleaners, grass cutters, winches, conveyors, slews, sweeper drives, augers, cutters, mowers and chippers.

Specification

ModelATO-OMP-50
Shaft Type (Optional)Flat Key, Splined
Flange Type (Optional)2 Bolts, 4 Bolts
Displacement50cc/rev (50cm3/rev)
Working Pressure15 MPa
FlowContinuous38LPM
Intermittent45LPM
Max.SpeedContinuous698rpm
Intermittent859rpm
PressureContinuous124∆Bar
Intermittent138∆Bar
TorqueContinuous73Nm
Intermittent84Nm
Weight6.5kg

Note:

  • A simultaneous maximum torque and maximum speed are not recommended.
  • ∆Bar refers to true pressure difference between inlet port and outlet port.
  • Continuous Rating means that the motor may be run continuously at these ratings.
  • Intermittent operation refers to that the motor running time must not exceed 10% per minute under this condition.

*To assure the best orbital motor life, run it for approximately one hour at 30% of rated pressure before application to full load. Be sure this motor is filled with fluid before any load applications.

Dimensions (Unit: mm)

Dimensions of hydraulic orbital motor

L1=140mm

Hydraulic Orbital Motor Shaft (Unit: mm)

motor shafts of hydraulic orbital motor

Flange Types (Unit: mm)

2 bolt flange hydraulic orbital motor

4 bolt flange hydraulic orbital motor

L=147mm

Details

Hydraulic Orbital Motor Details

Tips: Reasons for bubbles in hydraulic orbital motor

When the hydraulic orbital motor is being transported, a small amount of gas will be suspended in the gear oil as a spherical bubble with a small diameter during filling. Gas and gear oil melt into each other and will not change the physical properties of gear oil, but when gear oil melts some amount of gas and becomes saturated, it melts because of a sudden drop in pressure when it flows through the overflow valve or the inlet of the pump. A part of the saturated gas in the gear oil will be separated out and slowly gathered together, resulting in large bubbles.

Suppose the oil level in the hydraulic orbital motor's hydraulic oil tank is too low. In that case, the returned gear oil will appear on the surface of the oil tank and cause a lot of bubbles, and if the oil inlet pipe and the inlet of the hydraulic pump leak, there will be a lot of bubbles. The gas enters the hydraulic circulation system and bubbles appear.

Product reviews
Works pretty good
5
Matt
Avatar
3/23/2022 9:30 PM
Works great in our crane, the service is good. Seller gave us professional technical support. If we need more, we will contact you.
Was this review helpful? Yes No (0/0)
This hydraulic orbital motor runs smoothly
5
Kirk
Avatar
7/1/2026 7:05 PM
Very good hydraulic motor for industrial use. It runs smoothly in both continuous and intermittent conditions, and the torque output is strong enough for our mining equipment setup.
Was this review helpful? Yes No (0/0)
Only registered users can write reviews
Customers who bought this item also bought

Hydraulic Orbital Motor, 200cc/rev

ATO-HOM-200
$322.89
Low speed high torque hydraulic orbital motor at affordable price. It is a spool valve motor with 200cc/r displacement, reliable operation and high efficiency, selectable flat key shaft or splined shaft, and mounting flanges of 2 bolts and 4 bolts. This orbit motor can be used in parallel or in series.