24V-60V Brushless DC Motor Controller for 24/36/48/60V BLDC Motor

$473.06
Low cost BLDC motor controller works at 24V to 60V power supply to control speed for 24/36/48/60V 3 phase BLDC motor. Rated current 75A, 50 rpm in hall sensor motor and 1 rpm in encoder sensor. This brushless electric motor driver should be installed in a well-ventilated environment.
SKU: ATO-BLDC-C100
*
Free Shipping
Delivery date: 6-12 days

Brushless direct current motor controller with RS-485 communication design, low voltage and precise positioning control, adapts to BLDC motor control based on hall sensor, magnetic coding sensor and photoelectric coding sensor.

Specification

ModelATO-BD100 (Click it to view more controller specs)
Matching Electric Motor ModelATO-BLDC-1500R3 (1.5 kW 36V/48V BLDC Motor)
ATO-GEAR-W1500 (1.5 kW 36V/48V DC Worm Gear Motor)
ATO-GEAR-W2000 (2 kW 48V DC Worm Gear Motor)
ATO-GEAR-P1500 (1.5 kW 36V/48V DC Planetary Gear Motor)
ATO-GEAR-P2000 (2 kW 48V DC Planetary Gear Motor)
Rated Current75A
Rated Input Voltage RangeDC +24~ +72V
Operating Temperature Range-40-+80℃
IO InputSupports NPN, PNP
NPN: 0V is low, 5~24V is high, current 20mA
PNP: 13V high output, low to ground
IO OutputOpen Drain NPN Output Voltage: not exceed 30V, Current: 500mA
SV Input CharacteristicsDC 0-5V Range or DC 0-10V Range
Deadband Voltage Adjustment Range: 0.2~1.0V
Input Internal Resistance:100k
PWM Input CharacteristicsFrequency Range: 1~10kHz (50% duty cycle)
Duty Cycle Range:0~100%(100Hz-1000Hz)
Signal Voltage: DC 5~24V
Carrier Frequency10~20kHz
485 Communication ParametersID: 1~255
Baud Rate: 9600/19200/38400/57600/115200 bps
CAN Communication ParametersID: 0~255
Baud Rate: 125/250/500 kbps
Load150% of Rated Current
Overload Duration: 30~1s (at 150% Rated)
External Temperature SensorCustomizable
ntc=mf52-103f-3435-55l
Control MethodTorque Loop (Open Loop) Speed Loop (Close Loop)
Acceleration and Deceleration Times0.5-16s Motor Without Load
Overheating ProtectionInside the Driver:+85℃
Note*
  1. RS485 (Modbus RTU) and CAN Bus cannot be used at the same time.
  2. VRM and PWM cannot be used at the same time.


Dimensions (Unit: mm)

Dimensions of Brushless DC Motor Driver 24V 60V

Note:

  • Please install, connect, and debug the motor controller with industry technicians.
  • It is not allowed to install, remove, or replace the circuit of the motor controller when it is live.
  • Be sure to install necessary protective devices between the power input and the power supply (battery) to avoid dangerous accidents or fatal injuries.
  • Need to install: overcurrent protector, insurance, emergency switch.
  • Please do the isolation and insulation protection between the motor controller and the ground and equipment.
  • If there is a real need for live debugging of this motor controller, please choose a non-metallic well-insulated screwdriver or special debugging tool.
  • This motor controller shall be installed in a well-ventilated environment.
  • This motor controller cannot be directly used in high humidity, dust, corrosive gas, or strong vibration of the abnormal environment.

Details

24V-60V Brushless DC Motor Controller Details

Tips: Brushless DC motor controller troubleshooting

The motor does not rotate.

  • Insufficient voltage. Test whether the voltage of the third pin of the MCU exceeds 3.2V.
  • Whether the brake level connection method is normal, check pin 7 of the MCU, the voltage of the high-level brake exceeds 2.5V, and the voltage of the low-level brake exceeds 2.0V.
  • Whether the speed regulating voltage is added to the 5th pin of the MCU.
  • The connector is improperly installed, and the output cannot be output due to lack of phase.
  • When the above conditions are met, the output and drive circuit malfunctions, the external force forces the motor to rotate, and there is obvious uneven resistance inside, the MOS power tube is damaged, but some of the front-end drive transistors are damaged..

The motor rotates, but abnormal.

  • Check whether the controller's working mode of 60 degrees and 120 degrees corresponds to it.
  • The motor is the ability of external force, there is a loud operating sound when rotating, and the output is not stable. Check the condition of the connection line. The components of the circuit board have missing welding, virtual welding, short circuit, wrong welding, etc.
  • Hall signal error, some motors need to adjust the output line and Hall signal line of the controller
  • The motor is unstable when rotating at low speed, and the parameters of the drive circuit components are too different. Test whether the three-phase drive components are welded incorrectly, and the performance is different.

The motor is easy to stop and the load capacity is poor.

  • Whether the controller short-circuit comparison resistance R9, R10 is 20K or 1.2K.
  • Capacitor C7 (1000Pf), dead zone adjustment capacitor C24 (100PF) capacity deviation is too large
  • Constantan wire is too long (When the capacity of the controller capacitor C7, C24 is wrong, the working current is abnormal, the general working current is large, and the constantan is too long)
  • Some parts of the drive circuit are leaking and have poor performance.

The current-limiting resistor is heated, and the static current is too large.

  • There is a short circuit in the detection circuit.
  • Whether the driver output has a component welding error.
  • Whether the connection in the plug-in corresponds.

Flammable MOS tube or motor runs normally at low speed, and when the handle rises quickly, the flammable MOS tube.

  • Check whether the HC27 circuit (U3) normal.
  • The voltage of pin 21 of the single-chip microcomputer is not the high level or low level of the logic check, and its pull-up resistance is open or soldered.
  • The MOS drive signal cannot normally follow the output signal of the single-chip microcomputer, showing a normal level, and it is most likely to damage the MOS.

After adding the signal, the signal light goes out, but the motor does not rotate.

  • Whether the motor output is well connected.
  • The motor hall is not connected.
  • The drive circuit has equipment open circuit or false soldering, missing soldering, etc.

BLDC Motor Controller Circuit: 'IO + SV' Control

This video walks you through setting up a BLDC motor controller using the "Input/Output & Speed Voltage" method, covering control basics, required components, wiring, and operation.

Product reviews
Wonderful brushless dc motor controller
5
Pat
Avatar
3/22/2022 7:07 PM
This brushless dc motor controller works great. Did exactly what I wanted it to do. Works as described. Easy to wire up. I think everything is perfect. I highly recommend this motor controller if you need one.
Was this review helpful? Yes No (0/0)
Great brushless DC motor controller.
5
Brandon
Avatar
5/16/2022 2:06 AM
I used this BLDC motor controller to run a 1.5 kW brushless motor to work with feedback. I’ve gone through several other BLDC controllers and this one is the best at its price point. Great product and I will recommend this controller to others.
Was this review helpful? Yes No (0/0)
Is this a documentation error?
5
Duncan
Avatar
5/26/2022 3:12 AM
All documentation says the Vcc going to the motor from pin 6 on the ATO-BLD-100A is either 5 V or 6.25 V. when measured, it is running at a nominal 12V, is this a documentation error?
Was this review helpful? Yes No (0/0)
ATO Responded
This is normal, the Hall voltage will actually be higher, which can better anti-interference.
Ask about speed adjustment function
5
Jakko
Avatar
8/9/2023 12:27 AM
I want to ask about speed adjustment function.
https://www.ato.com/Content/doc/BLD100-BLDC-Motor-Controller-Manual.pdf
According to vi of this document, the rpm cannot exceed 4000 rpm. I want to accelerate speed to over 4000 rpm by using external analog speed signal. Is it possible? If it can, please tell me how to do.
Was this review helpful? Yes No (0/0)
ATO Responded
Unfortunately, the external analog signal can Not increase the rpm of the motor exceed 4000 rpm. The maximum rpm is related to the motor itself, because the rated speed of the motor is 3000 rpm, the controller can not increase the rpm of the motor exceed 4000 rpm.
Some questions about ATO-BLDC-C100.
5
Liam
Avatar
9/6/2023 9:39 PM
I ordered ato-bldc-c100 last month. I have two questions about ATO-BLDC-C100.
1. The delivered controller has only 2 dip switches. It seems different from this page.
Brushless DC Motor Controller, 12V ~ 60V | ATO.com
Did the controller version change?

2. Motor speed does not increase above 7500 rpm. What could be the reason?
Below is the test condition.
$(D),  DC :48VDC
$(D),  OPEN LOOP (SW2:OFF)
$(D),  Knob is turned fully clockwise
$(D),  At 7500rpm, U phase Voltage is 36 [V], U phase Ampere is 18 [Arms], Out put power is 920 [W]
Was this review helpful? Yes No (0/0)
ATO Responded
1. Yes, our controller has been upgraded, and the upgraded version only has 2 dip switches.

2. Please provide us your motor parameter table and manual for further confirmation.
We are having issues with the new motor controllers
4
Enlina
Avatar
11/19/2024 12:18 AM
We've been using 38400 as baud rate, yet we see the manual says 9600. When in rs485 mode, the controller often starts in the wrong direction and at 3000 rpm max speed. We stop the motor, restart it, it goes the correct direction but still at 3000rpm max. What do you think is going on?
Was this review helpful? Yes No (0/0)
ATO Responded
The baud rate can be 38400, no problem. For RS485 communication, you can refer to our demonstration video, see on: https://www.youtube.com/watch?v=_vizSqQl5K0
flyback diodes
5
Tojya
Avatar
12/5/2024 12:50 PM
Hi! Are external flyback diodes required or are they already built in to the motor controller?
Was this review helpful? Yes No (0/0)
ATO Responded
Normally, there is no need to add flyback diodes externally, but I don’t know what port/position you want to add them to. You can tell us.
It performs very well and is worth the price
5
Martin
Avatar
9/25/2025 12:21 AM
Used to control my 48V BLDC motor, 75A rated current handles load well. RS-485 works smoothly, but need good ventilation, no overheating so far, worth the price.
Was this review helpful? Yes No (0/0)
Number of Motors Controlled
5
Kylia
Avatar
1/4/2026 11:33 PM
Can this controller control two brushless motors simultaneously? I need to be able to independently control the speed and direction of two motors at the same time.
Was this review helpful? Yes No (0/0)
ATO Responded
Sorry, this unit, ATO-BD100, cannot control two motors simultaneously; one controller can only control one motor.
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

Brushless direct current motor controller with RS-485 communication design, low voltage and precise positioning control, adapts to BLDC motor control based on hall sensor, magnetic coding sensor and photoelectric coding sensor.

Specification

ModelATO-BD100 (Click it to view more controller specs)
Matching Electric Motor ModelATO-BLDC-1500R3 (1.5 kW 36V/48V BLDC Motor)
ATO-GEAR-W1500 (1.5 kW 36V/48V DC Worm Gear Motor)
ATO-GEAR-W2000 (2 kW 48V DC Worm Gear Motor)
ATO-GEAR-P1500 (1.5 kW 36V/48V DC Planetary Gear Motor)
ATO-GEAR-P2000 (2 kW 48V DC Planetary Gear Motor)
Rated Current75A
Rated Input Voltage RangeDC +24~ +72V
Operating Temperature Range-40-+80℃
IO InputSupports NPN, PNP
NPN: 0V is low, 5~24V is high, current 20mA
PNP: 13V high output, low to ground
IO OutputOpen Drain NPN Output Voltage: not exceed 30V, Current: 500mA
SV Input CharacteristicsDC 0-5V Range or DC 0-10V Range
Deadband Voltage Adjustment Range: 0.2~1.0V
Input Internal Resistance:100k
PWM Input CharacteristicsFrequency Range: 1~10kHz (50% duty cycle)
Duty Cycle Range:0~100%(100Hz-1000Hz)
Signal Voltage: DC 5~24V
Carrier Frequency10~20kHz
485 Communication ParametersID: 1~255
Baud Rate: 9600/19200/38400/57600/115200 bps
CAN Communication ParametersID: 0~255
Baud Rate: 125/250/500 kbps
Load150% of Rated Current
Overload Duration: 30~1s (at 150% Rated)
External Temperature SensorCustomizable
ntc=mf52-103f-3435-55l
Control MethodTorque Loop (Open Loop) Speed Loop (Close Loop)
Acceleration and Deceleration Times0.5-16s Motor Without Load
Overheating ProtectionInside the Driver:+85℃
Note*
  1. RS485 (Modbus RTU) and CAN Bus cannot be used at the same time.
  2. VRM and PWM cannot be used at the same time.


Dimensions (Unit: mm)

Dimensions of Brushless DC Motor Driver 24V 60V

Note:

  • Please install, connect, and debug the motor controller with industry technicians.
  • It is not allowed to install, remove, or replace the circuit of the motor controller when it is live.
  • Be sure to install necessary protective devices between the power input and the power supply (battery) to avoid dangerous accidents or fatal injuries.
  • Need to install: overcurrent protector, insurance, emergency switch.
  • Please do the isolation and insulation protection between the motor controller and the ground and equipment.
  • If there is a real need for live debugging of this motor controller, please choose a non-metallic well-insulated screwdriver or special debugging tool.
  • This motor controller shall be installed in a well-ventilated environment.
  • This motor controller cannot be directly used in high humidity, dust, corrosive gas, or strong vibration of the abnormal environment.

Details

24V-60V Brushless DC Motor Controller Details

Tips: Brushless DC motor controller troubleshooting

The motor does not rotate.

  • Insufficient voltage. Test whether the voltage of the third pin of the MCU exceeds 3.2V.
  • Whether the brake level connection method is normal, check pin 7 of the MCU, the voltage of the high-level brake exceeds 2.5V, and the voltage of the low-level brake exceeds 2.0V.
  • Whether the speed regulating voltage is added to the 5th pin of the MCU.
  • The connector is improperly installed, and the output cannot be output due to lack of phase.
  • When the above conditions are met, the output and drive circuit malfunctions, the external force forces the motor to rotate, and there is obvious uneven resistance inside, the MOS power tube is damaged, but some of the front-end drive transistors are damaged..

The motor rotates, but abnormal.

  • Check whether the controller's working mode of 60 degrees and 120 degrees corresponds to it.
  • The motor is the ability of external force, there is a loud operating sound when rotating, and the output is not stable. Check the condition of the connection line. The components of the circuit board have missing welding, virtual welding, short circuit, wrong welding, etc.
  • Hall signal error, some motors need to adjust the output line and Hall signal line of the controller
  • The motor is unstable when rotating at low speed, and the parameters of the drive circuit components are too different. Test whether the three-phase drive components are welded incorrectly, and the performance is different.

The motor is easy to stop and the load capacity is poor.

  • Whether the controller short-circuit comparison resistance R9, R10 is 20K or 1.2K.
  • Capacitor C7 (1000Pf), dead zone adjustment capacitor C24 (100PF) capacity deviation is too large
  • Constantan wire is too long (When the capacity of the controller capacitor C7, C24 is wrong, the working current is abnormal, the general working current is large, and the constantan is too long)
  • Some parts of the drive circuit are leaking and have poor performance.

The current-limiting resistor is heated, and the static current is too large.

  • There is a short circuit in the detection circuit.
  • Whether the driver output has a component welding error.
  • Whether the connection in the plug-in corresponds.

Flammable MOS tube or motor runs normally at low speed, and when the handle rises quickly, the flammable MOS tube.

  • Check whether the HC27 circuit (U3) normal.
  • The voltage of pin 21 of the single-chip microcomputer is not the high level or low level of the logic check, and its pull-up resistance is open or soldered.
  • The MOS drive signal cannot normally follow the output signal of the single-chip microcomputer, showing a normal level, and it is most likely to damage the MOS.

After adding the signal, the signal light goes out, but the motor does not rotate.

  • Whether the motor output is well connected.
  • The motor hall is not connected.
  • The drive circuit has equipment open circuit or false soldering, missing soldering, etc.
Product reviews
Wonderful brushless dc motor controller
5
Pat
Avatar
3/22/2022 7:07 PM
This brushless dc motor controller works great. Did exactly what I wanted it to do. Works as described. Easy to wire up. I think everything is perfect. I highly recommend this motor controller if you need one.
Was this review helpful? Yes No (0/0)
Great brushless DC motor controller.
5
Brandon
Avatar
5/16/2022 2:06 AM
I used this BLDC motor controller to run a 1.5 kW brushless motor to work with feedback. I’ve gone through several other BLDC controllers and this one is the best at its price point. Great product and I will recommend this controller to others.
Was this review helpful? Yes No (0/0)
Is this a documentation error?
5
Duncan
Avatar
5/26/2022 3:12 AM
All documentation says the Vcc going to the motor from pin 6 on the ATO-BLD-100A is either 5 V or 6.25 V. when measured, it is running at a nominal 12V, is this a documentation error?
Was this review helpful? Yes No (0/0)
ATO Responded
This is normal, the Hall voltage will actually be higher, which can better anti-interference.
Ask about speed adjustment function
5
Jakko
Avatar
8/9/2023 12:27 AM
I want to ask about speed adjustment function.
https://www.ato.com/Content/doc/BLD100-BLDC-Motor-Controller-Manual.pdf
According to vi of this document, the rpm cannot exceed 4000 rpm. I want to accelerate speed to over 4000 rpm by using external analog speed signal. Is it possible? If it can, please tell me how to do.
Was this review helpful? Yes No (0/0)
ATO Responded
Unfortunately, the external analog signal can Not increase the rpm of the motor exceed 4000 rpm. The maximum rpm is related to the motor itself, because the rated speed of the motor is 3000 rpm, the controller can not increase the rpm of the motor exceed 4000 rpm.
Some questions about ATO-BLDC-C100.
5
Liam
Avatar
9/6/2023 9:39 PM
I ordered ato-bldc-c100 last month. I have two questions about ATO-BLDC-C100.
1. The delivered controller has only 2 dip switches. It seems different from this page.
Brushless DC Motor Controller, 12V ~ 60V | ATO.com
Did the controller version change?

2. Motor speed does not increase above 7500 rpm. What could be the reason?
Below is the test condition.
$(D),  DC :48VDC
$(D),  OPEN LOOP (SW2:OFF)
$(D),  Knob is turned fully clockwise
$(D),  At 7500rpm, U phase Voltage is 36 [V], U phase Ampere is 18 [Arms], Out put power is 920 [W]
Was this review helpful? Yes No (0/0)
ATO Responded
1. Yes, our controller has been upgraded, and the upgraded version only has 2 dip switches.

2. Please provide us your motor parameter table and manual for further confirmation.
We are having issues with the new motor controllers
4
Enlina
Avatar
11/19/2024 12:18 AM
We've been using 38400 as baud rate, yet we see the manual says 9600. When in rs485 mode, the controller often starts in the wrong direction and at 3000 rpm max speed. We stop the motor, restart it, it goes the correct direction but still at 3000rpm max. What do you think is going on?
Was this review helpful? Yes No (0/0)
ATO Responded
The baud rate can be 38400, no problem. For RS485 communication, you can refer to our demonstration video, see on: https://www.youtube.com/watch?v=_vizSqQl5K0
flyback diodes
5
Tojya
Avatar
12/5/2024 12:50 PM
Hi! Are external flyback diodes required or are they already built in to the motor controller?
Was this review helpful? Yes No (0/0)
ATO Responded
Normally, there is no need to add flyback diodes externally, but I don’t know what port/position you want to add them to. You can tell us.
It performs very well and is worth the price
5
Martin
Avatar
9/25/2025 12:21 AM
Used to control my 48V BLDC motor, 75A rated current handles load well. RS-485 works smoothly, but need good ventilation, no overheating so far, worth the price.
Was this review helpful? Yes No (0/0)
Number of Motors Controlled
5
Kylia
Avatar
1/4/2026 11:33 PM
Can this controller control two brushless motors simultaneously? I need to be able to independently control the speed and direction of two motors at the same time.
Was this review helpful? Yes No (0/0)
ATO Responded
Sorry, this unit, ATO-BD100, cannot control two motors simultaneously; one controller can only control one motor.
Only registered users can write reviews
Customers who bought this item also bought

1 hp (750W) Brushless DC Motor, 24V/48V/72V, 2.4 Nm

ATO-BLDC-750R3
$352.77
1 hp (750W) brushless DC electric motor with reasonable price, 3 phase 4 pair of poles design, 3000 rpm rated speed, 2.3 Nm holding torque, works at 24V/48V DC power supply. Buy BLDC motor controller and gearbox combines with the BLDC motor will provide you higher torque.

2 hp (1.5 kW) Brushless DC Motor, 36V/48V, 4.78 Nm

ATO-BLDC-1500R3
$432.36
Buy best 1500 watt brushless DC motor kit (3 phase BLDC motor and controller) at low price for your electric car. Motor features 3000 rpm rated speed, 4.78 Nm holding torque, peak torque up to 14.33 Nm, working at 36V / 48V DC power supply.

24V-60V Brushless DC Motor Controller for 36/48V BLDC Motor

ATO-BLDC-C50
$283.36
Low price brushless DC motor controller works at 24V to 60V power supply to control speed for 36V/ 48V BLDC motor. This motor driver is equipped with a variety of communication interfaces, and can realize different mode control, PWM open loop and speed closed loop.

48V DC 1000W Switching Power Supply

ATO-SMPS-1000-48
$197.54
Upgrade switch power supply, 48V DC 1000W, with shortage protection, overload protection, over-voltage protection. Wide input voltage range, steady and precise output voltage. Great power transformer for electronic equipment, Led Lighting, home appliance etc.

1/2 hp Brushless DC Motor, 24/36V, 2 Nm, 2000 rpm

ATO-BLDC-400R2
$358.25
Affordable price 400W (1/2 hp) brushless DC motor for sale, 24V/ 36V working voltage, 2000 rpm low speed, 2 Nm hold torque, IP54 for protection. The matched 3 phase BLDC motor controller, gearbox and adding 24V brake option are provided.