Load cell transmitter has external zero debugging and external span debugging functions, output standard signal 0-5V/0-10V/4-20mA.
Specification:
| Model | ATO-LCTR-DY510 |
| Accuracy | ±0.05%FS |
| Input signal | 0-20mV |
| Excitation voltage for load cell | 5V |
| Output signal (DC) * | 0-±5V/0-±10V/4-20mA |
| Power supply | DC 18-30V |
Load cell transmitter dimension drawing:
Load cell transmitter wiring diagram:
Load cell transmitter span debugging and zero debugging

Product reviews
Load cell transmitter is good for s type load cell
Lange
12/20/2018 6:45 PM
After the load cell transmitter is combined with the s type load cell, the external disturbance is much smaller. And the load cell transmitter works very stably. There is no difference between the original transmitter and this load cell transmitter on accuracy. However, the original transmitter is much more expensive than this one.
Was this review helpful? (0/0)
Can I customize the load cell I need?
Parton
11/10/2021 7:26 PM
Can you customize your load cell to be stainless steel?
Was this review helpful? (0/0)
How can the load cell transmitter work normally?
Glenn
11/23/2021 11:43 PM
Can your load cell transmitter ATO-LCTR-OA be supplied via 12VDC (battery of 12-14 volts) or does it need an additional DC-DC converter 12V DC to 24V DC power supply for proper operation?
Was this review helpful? (0/0)
Can the output of the load cell be selected on site?
Chantalv
12/1/2021 1:34 AM
Does the "load cell transmitter, output 0-5V/0-10V/4-20mA/0-20mA" output, so I can choose on site?
Was this review helpful? (0/0)
What is your load cell output signal and sensitivity?
Andrewk
12/16/2021 11:14 PM
What is your load cell output signal and sensitivity?
Was this review helpful? (0/0)
I’m searching for a signal conditioner for a load cell.
Albin
5/30/2022 12:07 AM
I’m searching for a signal conditioner for a load cell to reduce noise/ other disturbance and improve accuracy on a weighing machine. The load cell has a 10kg capacity, an excitation voltage of 10V, and an output of 0-20mv. I was looking at the ATO-LCTR-DY510 as a potential solution but I’m not sure if it will be compatible with the target machine. Currently, the load cell connects directly to the machine without an external amplifier and I was concerned that the 0-5V output of the transmitter will be too high. Would there be other solutions from ATO (potentially passive or active filters) that could be applicable?
Was this review helpful? (0/0)
I have incorrectly configured the load cell transmitter.
Izan
7/27/2022 12:37 AM
How can I factory reset the load cell transmitter?
Was this review helpful? (0/0)
Do you have troubleshooting ideas and/or a manual for both products?
Peterson
7/27/2022 1:34 AM
I have an ATO-TQS-SO4 paired with ATO-LCTR-OA rated for 20Nm and an output of 0 - 10V, but I am having trouble using it. No matter how much torque I apply, the voltage output remains the same, even when I apply no torque to the load cell. Do you have troubleshooting ideas and/or a manual for both products?
Was this review helpful? (0/0)
May I know where to connect the Reference (+) & (-) ?
Lay
3/2/2023 11:57 PM
With reference to the below, Received the device.
1. Red Excitation
2. Blue - Excitation
3. Yellow Signal
4. Green - Signal
5. White Reference
6. Black – Reference
Above mentioned is the wiring of existing Load cell and in your transmitter, there is only 4 wires. May I know where to connect the Reference (+) & (-) ?
1. Red Excitation
2. Blue - Excitation
3. Yellow Signal
4. Green - Signal
5. White Reference
6. Black – Reference
Above mentioned is the wiring of existing Load cell and in your transmitter, there is only 4 wires. May I know where to connect the Reference (+) & (-) ?
Was this review helpful? (0/0)
If you have any advice to fix my load cell problem?
amos
6/6/2023 3:05 AM
I’ve bought two kits of load cell with weight transmitter from you on February 23rd 2023.
I received one ATO-LCTR-OA labeled with a red “A” sticker and one with a red “B” sticker. I’m wondering If maybe I got the wrong model for one of the two? Also, I received one with the span and zero adjustment screw glued in place, while the other where free to spin around.
The weight transmitter labeled B has adjustable screw. It’s giving me wildly variable reading with nothing on the scale while the “A” transmitter stays put. I’d like to know what you warranty is like and if you have any advice to fix my problem.
I received one ATO-LCTR-OA labeled with a red “A” sticker and one with a red “B” sticker. I’m wondering If maybe I got the wrong model for one of the two? Also, I received one with the span and zero adjustment screw glued in place, while the other where free to spin around.
The weight transmitter labeled B has adjustable screw. It’s giving me wildly variable reading with nothing on the scale while the “A” transmitter stays put. I’d like to know what you warranty is like and if you have any advice to fix my problem.
Was this review helpful? (0/0)
Can load cell display below read in "lbs"?
kari
7/24/2023 2:13 AM
Our load cell display below can read in "lbs", right?
Was this review helpful? (0/0)
DATA SHEET
Yacine
4/29/2024 7:59 AM
I would like to draw your attention to the fact that the technical specifications displayed on this web page are different from the specifications provided in the PDF file, particularly regarding the input voltage. On the web page, it is listed as 0-20 mV, while in the PDF file, it is stated as 0.5-4 mV. Could you please confirm which one is correct so that I can make my decision?
Was this review helpful? (0/0)
Working voltage
Kangur
8/19/2026 1:54 AM
Can the transmitter model ATO-LCTR-OA operate on 18V DC power supply?
Was this review helpful? (0/0)
Only registered users can write reviews
Customers who bought this item also bought
Tension and Compression Load Cell, 1 kg - 500 kg
ATO-LC-TC01
$137.98
Tension and compression load cell can bear both tension and pressure, with good anti-eccentric load performance, low height, all sealed structure and complete specifications. Miniature load cell with optional capacity 1 kg/ 100kg/ 200 kg/ 300kg/ 500 kg is suited to use in restricted spaces, such as using in vehicle/test instrument/laminator measurement and control.
Single Point Load Cell, 300g/1kg/3kg/ 10kg/60kg/100kg/200kg to 500kg
ATO-LC-SP01
$79.89
Single point load cell is widely used for weighing scale or pricing scale. Single point load cell is suited to use in flat and low space, with parallel beam structure, good stability, good output symmetry, high accuracy, low temperature drift and overload protection.
Strain Gauge Load Cell, S type, 5kg/20kg/30kg/500kg to 7 ton
ATO-LC-S02
$82.59
S type load cell can bear both tension and pressure, with overload protection device, good output symmetry, high accuracy, compact structure and complete specifications. Strain gauge load cell can be applied for batching scale, electronic-mechanical scale, crane scales, automatic weighing instrument and other force value measurement and control.
Load Cell Junction Box for Scales, 2/3/4/6/8/10 Inlets to 1 Outlet
ATO-LCBOX-10I
$66.67
Multi-channel load cell junction box has 2/3/4/6/8/10 inlets and 1 outlet, aluminum alloy casing, good anti-interference, special for waterproof sealing joint, waterproof and dustproof rubber gasket for cover, easy to assemble and debug. Each channel can be adjusted balance to prevent damage to the sensor caused by inductive lightning and surge signals.
Micro Load Cell, S type, 1kg/2kg/3kg/10kg to 50kg
ATO-LC-S03
$142.38
S type load cell can bear both tension and pressure, with good stability, good output symmetry, high accuracy, low temperature drift, compact structure and complete specifications. Micro load cell is suited to use in restricted spaces.