Inductive Proximity Sensor, Metal Detection, PNP, M5

$39.95
M5 inductive proximity sensor, shielded and flush-mountable, reliably detects ferrous metals like steel and iron and non-ferrous metals like aluminum and brass up to 1 mm non-contact. Its compact brass housing with potted electronics ensures IP67 resistance to dust, washdown, and coolant. Operating from -30°C to 65°C, it fits robotic tooling, cylinder sensing, and shaft monitoring.
SKU: ATO-PROS-I5
*
Free Shipping
Delivery date: 6-12 days

Inductive proximity sensor with M5×1 thread and PNP output, available directly from the manufacturer. Its compact M5 design is especially suitable for space-constrained equipment and tight installation environments. Insulation impedance between the charging part and housing is ≥50MΩ (DC 500 megameter), ensuring robust electrical safety.

Functions

  • Red LED checks the state of the proximity sensor
  • High repeated positioning accuracy
  • High switching frequency
  • Wide voltage range 12-24V DC
  • Antivibration, dust, water and oil prevention
  • Reverse power protection, short circuit protection, directly connecting with PLC
  • PNP output positive signal for PLC, NPN gives 0V, verify PLC input type
  • Can replace small switches and limit switches

Specification

ModelATO-PSI-5A1ZP
Installation typeShielded
All the output methodsDC typeNPNNO
NC
PNPNO
NC
2 wireNO
NC
Detection range1mm±10%
Setting distance0-0.7mm
Delay distance≤10% detection range
Detection objectMagnetic metal (the detection distance decreases when it is non-magnetic metal)
Standard detection objectIron 5*5*1mm
Response frequencyDC: 2kHz, AC: 50Hz
Supply voltageDC type: DC 12-24V (6-36V), impulse (p-p) 10% below; AC type: AC 110-220V (90-250V) 50/60Hz
Withstand voltageAC1000V 50/60Hz 1min between charging part and housing
Voltage influenceInside ±15% rated supply voltage range, at rated supply voltage value, inside ±10% detection distance
Consumption currentN/P type: ≤13mA, D type: ≤0.8mA, A type: ≤1.7mA
Control outputN/P type: ≤300mA, D type: ≤200mA, A type: ≤400mA
Loop protectionN/P/D type: reversal connection protection, surge absorption, load short-circuit protection; A type: surge absorption
Ambient temperature & humidityOperation temperature/storage temperature: -30~65℃ (no freeze, no dew); Operation humidity/storage humidity: 35~95%RH
Temperature influenceTemperature range -30~65℃, at +23℃, ±15% detection distance; Temperature range -25~60℃, at +23℃, ±10% detection distance
Insulation impedance≥50MΩ (DC500 megameter) between charging part and housing
MaterialHousing: Nickel-plated brass, Detection surface: ABS
Protection classIP67
Cable length1.2m


Dimensional drawing (unit: mm)

Proximity sensor inductive M5 dimensional drawing

Wiring diagram

Proximity sensor PNP wiring

Tips: What is the difference between NO and NC Inductive Proximity Sensor?

A Normally Open (NO) inductive proximity sensor keeps its output OFF (no signal) when no metal target is detected, and turns ON (delivers a positive voltage for PNP type) as soon as the target enters the sensing range. This makes a NO inductive proximity sensor ideal for simple presence detection, part counting, and positioning tasks where a signal is only required when the object is present.
In contrast, a Normally Closed (NC) sensor maintains a continuous ON signal under normal conditions, and switches OFF (drops to 0V) when the target is detected. NC is preferred for fail-safe control systems, because any broken wire or power loss also cuts the signal, immediately triggering an alarm or machine stop. When choosing between them, select NO for standard on-demand detection and NC for safety-critical circuits that require constant loop monitoring. Always verify your PLC input type (PNP or NPN) and wiring to ensure proper compatibility with your selected output logic.

ATO will use a proximity sensor and a digital counter to count number in the video.

In this video, ATO will show you top ten most used sensors (sensing technologies).

In this video, ATO will show you the  differences between inductive and magnetic types.

How to Use an Inductive Proximity Sensor?

This video demonstrates how to wire and use an inductive proximity sensor.

Product reviews
great proximity sensor
5
Ann
Avatar
9/14/2025 9:17 PM
I’ve been using this M5 inductive proximity sensor for a few weeks now and it’s been super reliable. Super accurate with metal detection even in dusty conditions. The value for money is honestly great compared to other brands, and it hooked up to my PLC without any issues.
Was this review helpful? Yes No (0/0)
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

Inductive proximity sensor with M5×1 thread and PNP output, available directly from the manufacturer. Its compact M5 design is especially suitable for space-constrained equipment and tight installation environments. Insulation impedance between the charging part and housing is ≥50MΩ (DC 500 megameter), ensuring robust electrical safety.

Functions

  • Red LED checks the state of the proximity sensor
  • High repeated positioning accuracy
  • High switching frequency
  • Wide voltage range 12-24V DC
  • Antivibration, dust, water and oil prevention
  • Reverse power protection, short circuit protection, directly connecting with PLC
  • PNP output positive signal for PLC, NPN gives 0V, verify PLC input type
  • Can replace small switches and limit switches

Specification

ModelATO-PSI-5A1ZP
Installation typeShielded
All the output methodsDC typeNPNNO
NC
PNPNO
NC
2 wireNO
NC
Detection range1mm±10%
Setting distance0-0.7mm
Delay distance≤10% detection range
Detection objectMagnetic metal (the detection distance decreases when it is non-magnetic metal)
Standard detection objectIron 5*5*1mm
Response frequencyDC: 2kHz, AC: 50Hz
Supply voltageDC type: DC 12-24V (6-36V), impulse (p-p) 10% below; AC type: AC 110-220V (90-250V) 50/60Hz
Withstand voltageAC1000V 50/60Hz 1min between charging part and housing
Voltage influenceInside ±15% rated supply voltage range, at rated supply voltage value, inside ±10% detection distance
Consumption currentN/P type: ≤13mA, D type: ≤0.8mA, A type: ≤1.7mA
Control outputN/P type: ≤300mA, D type: ≤200mA, A type: ≤400mA
Loop protectionN/P/D type: reversal connection protection, surge absorption, load short-circuit protection; A type: surge absorption
Ambient temperature & humidityOperation temperature/storage temperature: -30~65℃ (no freeze, no dew); Operation humidity/storage humidity: 35~95%RH
Temperature influenceTemperature range -30~65℃, at +23℃, ±15% detection distance; Temperature range -25~60℃, at +23℃, ±10% detection distance
Insulation impedance≥50MΩ (DC500 megameter) between charging part and housing
MaterialHousing: Nickel-plated brass, Detection surface: ABS
Protection classIP67
Cable length1.2m


Dimensional drawing (unit: mm)

Proximity sensor inductive M5 dimensional drawing

Wiring diagram

Proximity sensor PNP wiring

Tips: What is the difference between NO and NC Inductive Proximity Sensor?

A Normally Open (NO) inductive proximity sensor keeps its output OFF (no signal) when no metal target is detected, and turns ON (delivers a positive voltage for PNP type) as soon as the target enters the sensing range. This makes a NO inductive proximity sensor ideal for simple presence detection, part counting, and positioning tasks where a signal is only required when the object is present.
In contrast, a Normally Closed (NC) sensor maintains a continuous ON signal under normal conditions, and switches OFF (drops to 0V) when the target is detected. NC is preferred for fail-safe control systems, because any broken wire or power loss also cuts the signal, immediately triggering an alarm or machine stop. When choosing between them, select NO for standard on-demand detection and NC for safety-critical circuits that require constant loop monitoring. Always verify your PLC input type (PNP or NPN) and wiring to ensure proper compatibility with your selected output logic.

Product reviews
great proximity sensor
5
Ann
Avatar
9/14/2025 9:17 PM
I’ve been using this M5 inductive proximity sensor for a few weeks now and it’s been super reliable. Super accurate with metal detection even in dusty conditions. The value for money is honestly great compared to other brands, and it hooked up to my PLC without any issues.
Was this review helpful? Yes No (0/0)
Only registered users can write reviews
Customers who bought this item also bought

Proximity Sensor, Inductive, NPN, NO/NC, 4 mm

ATO-PROS-I4
$39.95
4mm proximity sensor can detect a variety of metals, miniature size, long life, low price, shielded type installation, anti-interference ability, 1mm detection distance, using for precise positioning of molds, precision machine tools and robots. The inductive proximity sensor is used to detect magnetic metals (for non-magnetic metals, the detection range is reduced).