Capacitive proximity sensor with M18*1 thread, NPN type output, manufacturer direct sale. The proximity sensor has an IP67 protection level and is dustproof and waterproof.
Functions
- Red LED checks the state of proximity sensor
- High repeated positioning accuracy
- High switching frequency
- Wide voltage range
- Antivibration, dust, water and oil prevention
- Reverse power protection, short circuit protection, directly connecting with PLC
Specification
| Model | ATO-PSC-18ABZ | |||
| Installation type | Unshielded | Shielded | ||
| All the output methods | DC type | NPN | NO | NO |
| NC | NC | |||
| PNP | NO | NO | ||
| NC | NC | |||
| AC type | 2 wire | NO | NO | |
| NC | NC | |||
| Detection range | 10mm±10% | 5mm±10% | ||
| Setting distance | 0-8mm | 0-4mm | ||
| Delay distance | ≤10% detection range | |||
| Detection object | Any dielectric substance | |||
| Standard detection object | SPCC iron 50*50*1mm | |||
| Response frequency | DC: 0.5kHz, AC: 25Hz | |||
| Supply voltage | DC type: DC 12-24V (6-36V), impulse (p-p) 10% below; AC type: AC 110-220V (90-250V) 50/60Hz | |||
| Withstand voltage | AC1000V 50/60Hz 1min between charging part and housing | |||
| Voltage influence | Inside ±15% rated supply voltage range, at rated supply voltage value, inside ±10% detection distance | |||
| Consumption current | N/P type: ≤13mA, D type: ≤0.8mA, A type: ≤1.7mA | |||
| Control output | N/P type: ≤300mA, D type: ≤200mA, A type: ≤400mA | |||
| Loop protection | N/P/D type: reversal connection protection, surge absorption, load short-circuit protection, A type: surge absorption | |||
| Ambient temperature & humidity | Operation temperature/storage temperature: -30~65℃ (no freeze, no dew); Operation humidity/storage humidity: 35~95%RH | |||
| Temperature influence | Temperature range -30~65℃, at +23℃, ±15% detection distance; Temperature range -25~60℃, at +23℃, ±10% detection distance | |||
| Insulation impedance | ≥50MΩ (DC500 megameter) between charging part and housing | |||
| Material | Housing: Nickel plated brass, Detection surface: ABS | |||
| Protection class | IP67 | |||
| Cable length | 1.2m | |||
Dimensional drawing (unit: mm)

Wiring diagram

Tips: Types of proximity sensor
- According to the working principle, proximity sensors can be divided into:
Inductive type: Used to detect a variety of metals
Capacitance type: Used to detect a variety of conductive or non-conductive liquid or solid
Photoelectric type: Used to detect all lightproof materials
Ultrasonic type: Used to detect the material that ultrasonic wave cannot pass through
Electro-magnetic induction type: Used detect magnetic or non-magnetic metal - According to design and shape, they can be divided into cylindrical type, square type, and ditch type, perforating type and separated type.
Cylindrical type is more convenient in the installation than square one with same detection features. The testing part of ditch-type is inside the groove for detecting objects that pass through the groove. Perforating type is used for small parts of small screws or balls, and assembles with buoys into a level detection device. - According to power supply method, they can be divided into DC type and AC type.
- According to the output form, they can be divided into DC two-wire type, DC three-wire type, DC four-wire type, AC two-wire type and AC three-wire type.
Product reviews
Good product, good price
Leo
3/30/2022 8:42 PM
This sensor works perfectly on my 3D printer. Tied right into 6 volt supply. It works as it should and very consistent. It gave very accurate readings every time. Good product!
Was this review helpful? (0/0)
Do you have any suggestions to make it work?
Guyenng
8/3/2023 12:50 AM
I am attempting to sense when a tennis ball goes between the two photoelectric sensors. The sensors are about 8 inches apart. The sensors are being powered by 12VDC, the output cable goes to a voltage divider (which reduces the voltage from 12V to about 2.5 V) and then to an Arduino. Based on my calculations, the ball is between the sensors for about 7 ms, which is more than the 1 ms reaction time for the sensors. The sensors pick up slower moving objects. Would increasing the voltage make them more sensitive? Would a different material (other than a tennis ball) work better? Could I have accidently damaged the sensors, which reduced the reaction time? Do you have any suggestions to make it work?
Was this review helpful? (0/0)
Only registered users can write reviews
Customers who bought this item also bought
Proximity Sensor, Inductive, M18, 3 Wire, 120V
ATO-PROS-I18
$39.45
M18 inductive proximity sensor can detect a variety of metals, small size, long life, cheap price, unshielded type installation, anti-interference ability, 8mm detection distance, supply voltage AC 120V, manufacturer direct sale. The delay distance of the inductive proximity sensor is ≤10% of the detection range, and the protection level reaches IP67, which can operate reliably in harsh industrial environments.
Capacitive Proximity Sensor, M24, 2 Wire, 120V
ATO-PROS-C24
$39.34
M24 proximity sensor can detect nonmetal (or metal), plastic, water, liquid level and powder height, with small size, long life, low cost, 8mm detection distance, shielded type installation, anti-interference ability, manufacturer direct sale. The capacitive proximity sensor housing is made of nickel-plated brass, the detection surface is made of ABS plastic, and has an IP67 protection level.
Programmable Timer Relay, 8-Input 8-Output, 12V/24V DC
ATO-TIMER-16PLC
$127.65
8-input 8-output programmable timer relay, with 12V or 24V DC supply voltage, can work as simple PLC, with intelligent and humanized control, easy to learn, understand and operate. Optional 3 output forms of transistor DC output, transistor AC output and relay output. Input compatible with PNP/NPN. High reliability and competitive price.