PLC Controller, 10/14/20/30/48/60 I/O, Relay/Transistor Output

$110.76
Economical Programmable Logic Controller is a basic PLC for sequential control and simple communication monitoring, supplied with AC power 100 ~ 240V 50/60Hz, program capacity 4k steps, selectable in the I/O points of 10/14/16/20/24/30/32/40/48/60, relay or transistor output type, cost-friendly and highly reliable.
SKU: ATO-PLC-EC3
*
Free Shipping
Delivery date: 6-12 days

Basic PLC (Programmable Logic Controller) DVP-EC3 is the most economical solution for sequence control and simple RS-485/Modbus communication.

Features

  • Built-in I/O: 10/14/16/20/24/30/32/40/48/60
  • Program capacity: 4k steps
  • COM port: Built-in RS232 & RS485 ports (10/14 I/O models do not support RS485), compatibale with Modbus ASCII/RTU protocol
  • Support 2 points (Y0, Y1) of independent high-speed (max. 10kHz) pulse output

Specification

ModelATO-DVP-EC3
Built-in I/O10 / 14 / 16 / 20 / 24 / 30 / 32 / 40 / 48 / 60
Power Supply100 ~ 240V AC (-15% ~ +10%), 50/60Hz ±5%
OperationATO-DVP-EC3 series PLC starts to run when the power supply rises to 95-100V AC and stops when the power supply  drops down to 70V AC.
It continues running for 10ms after the power is cut off.
Power Supply Fuse2A / 250V AC
Power Consumption10/14/16 I/O: 12VA
20/24/30/32/40 I/O: 15.6VA
48/60 I/O: 22.5VA
DC 24V Current Output *110/14/16 I/O: 200mA
20/24/30/32/40 I/O: 300mA
48/60 I/O: 400mA
Power Supply ProtectionDC 24V output short circuit protection
Voltage Withstand1500VAC (Primary-secondary), 1500VAC (Primary-PE), 500VAC (Secondary-PE)
Insulation Resistance>5MΩ at 500VDC (between all I/O points and ground)
Noise ImmunityESD (IEC 61131-2, IEC 61000-4-2): 8kV Air Discharge
EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2kV, Digital I/O: 1kV, Analog & Communication I/O: 1kV
RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m
GroundingThe diameter of grounding wire shall not be less than that of L, N terminal of the power supply.
(When many PLCs are in use at the same time, please make sure every PLC is properly grounded.)
EnvironmentOperation: 0°C~55°C (temperature), 5~95% (humidity), pollution degree 2
Storage: -25°C~70°C (temperature), 5~95% (humidity)
ApprovalsUL508, European community EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC
Vibration/Shock ImmunityInternational standards: IEC61131-2, IEC 68-2-6 (TEST Fc)/ IEC61131-2 & IEC 68-2-27 (TEST Ea)
RS485 Port10/14 I/O models do not support RS485, other models is available
WeightSee below "Selection Table"
Note:
*1. It is suggested that the power output should not be supplied to HMIs.

Selection Table

ModelBuilit-in I/ONumber of Inputs
Number of Outputs
Output Type
COM PortWeight
DVP10EC00R31064RelayRS-232205g
DVP10EC00T31064TransistorRS-232192g
DVP14EC00R31486RelayRS-232210g
DVP14EC00T31486TransistorRS-232195g
DVP16EC00R31688RelayRS-232/RS-485220g
DVP16EC00T31688TransistorRS-232/RS-485198g
DVP20EC00R320128RelayRS-232/RS-485310g
DVP20EC00T320128TransistorRS-232/RS-485285g
DVP24EC00R3241212RelayRS-232/RS-485322g
DVP24EC00T3241212TransistorRS-232/RS-485288g
DVP30EC00R3301812RelayRS-232/RS-485325g
DVP30EC00T3301812TransistorRS-232/RS-485290g
DVP32EC00R3321616RelayRS-232/RS-485340g
DVP32EC00T3321616TransistorRS-232/RS-485295g
DVP40EC00R3402416RelayRS-232/RS-485380g
DVP40EC00T3402416TransistorRS-232/RS-485340g
DVP48EC00R3482820RelayRS-232/RS-485540g
DVP48EC00T3482820TransistorRS-232/RS-485505g
DVP60EC00R3603624RelayRS-232/RS-485560g
DVP60EC00T3603624TransistorRS-232/RS-485510g

PLC I/O Point Specification

Input Points
Input Point No.X0 ~ X3X4 ~ X17X20 ~  #1
Input Point TypeDigital input
Input FormDC (SINK or SOURCE)
Input Currrent24VDC, 5mA
Max. Input Frequency20kHz10kHz60Hz
Action LevelOff → On>15VDC
On → Off< 5VDC
Response TimeOff → On< 25μs< 50μs< 10ms
On → Off< 10μs< 20μs< 15ms
Filter TimeX0 ~ X17Approx. 10ms (0~20ms adjustable in D1020, D1021)
Output Points
Output Point TypeRelay - RTransistor - T
Voltage Specification< 240VAC, 30VDC5 ~ 30VDC #2
Max. Output Frequency1HzNormal inputs10kHz #4
Maximum LoadResistive2A/point (5A/COM)0.5A/1 point (4A/ZP)
Inductive#315W (30VDC)
Lamp20W DC/100W AC2.5W (30VDC)
Response TimeOff → OnApprox. 10ms< 30μs< 20μs
On → Off< 350μs< 50μs
Note:
#1. Please refer to “I/O Terminal Layouts” for the max. X/Y No. on each model.
#2. UP, ZP must work with external auxiliary power supply 24V DC (-15% ~ +20%), rated consumption approx. 1mA/point.
#3. Life curves
PLC Controller Life Curve
#4. The maximum frequency is applicable to Y0-Y3 in all DVP-EC3 series PLCs, and other output terminals are general terminals.

Dimensions

EC3 Series Programmable Logic Controller Dimensions

Model10EC00R/T314EC00R/T316EC00R/T320EC00R/T324EC00R/T330EC00R/T332EC00R/T340EC00R/T348EC00R/T360EC00R/T3
L95150164240
L186141155231

How to control a stepper motor using a PLC and HMI?

This video shows you how to configure a PLC, HMI, motor driver, and proximity sensor to perform Origin Return (OPR) control of a stepper motor.

Four Ways to Control VFD with PLC

This video introduces the main wiring methods between PLC and VFD, including digital control, analog control, serial communication and Ethernet connection. The choice of connection method depends on the specific application requirements, system complexity, cost considerations and the need for control accuracy and flexibility.

PLC and HMI Analog Output (0-10V) Programming

In this tutorial, we will walk you through the structured system setup between the HMI, PLC, and VFD, as well as the programming steps required for seamless operation.

Product reviews
PLC controller controls smoothly
5
Rogers
Avatar
3/16/2021 12:48 AM
I am using a PLC controller to control the speed and simple communication monitoring. The PLC controller runs and controls very smoothly, and I strongly recommend it to friends around me.
Was this review helpful? Yes No (0/0)
great little plc controller
4
Becky11
Avatar
10/10/2025 8:42 PM
I'm really impressed with the overall value of this PLC controller. It was easy to set up for a basic automation job and the built-in communication ports are a huge plus. My only small complaint is that the documentation could be a bit clearer in a few spots. But for the cost, it's a reliable workhorse.
Was this review helpful? Yes No (0/0)
Just installed this PLC to automate our packaging line
5
Joey
Avatar
10/19/2025 9:38 PM
It handles all our sensors and solenoids perfectly. Programming was straightforward with the free software, and the relay outputs directly control our motors. After running 24/7 for two months, no issues. It's much more reliable than the old timer relays we used before.
Was this review helpful? Yes No (0/0)
It's a practical choice for simple control tasks
5
Thomas
Avatar
10/29/2025 11:55 PM
I’ve been using this PLC for a few months now, and it’s been surprisingly solid. Setup was straightforward, and it runs my small automation setup without a hitch. The relay outputs respond quickly, and the build feels durable.
Was this review helpful? Yes No (0/0)
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

Basic PLC (Programmable Logic Controller) DVP-EC3 is the most economical solution for sequence control and simple RS-485/Modbus communication.

Features

  • Built-in I/O: 10/14/16/20/24/30/32/40/48/60
  • Program capacity: 4k steps
  • COM port: Built-in RS232 & RS485 ports (10/14 I/O models do not support RS485), compatibale with Modbus ASCII/RTU protocol
  • Support 2 points (Y0, Y1) of independent high-speed (max. 10kHz) pulse output

Specification

ModelATO-DVP-EC3
Built-in I/O10 / 14 / 16 / 20 / 24 / 30 / 32 / 40 / 48 / 60
Power Supply100 ~ 240V AC (-15% ~ +10%), 50/60Hz ±5%
OperationATO-DVP-EC3 series PLC starts to run when the power supply rises to 95-100V AC and stops when the power supply  drops down to 70V AC.
It continues running for 10ms after the power is cut off.
Power Supply Fuse2A / 250V AC
Power Consumption10/14/16 I/O: 12VA
20/24/30/32/40 I/O: 15.6VA
48/60 I/O: 22.5VA
DC 24V Current Output *110/14/16 I/O: 200mA
20/24/30/32/40 I/O: 300mA
48/60 I/O: 400mA
Power Supply ProtectionDC 24V output short circuit protection
Voltage Withstand1500VAC (Primary-secondary), 1500VAC (Primary-PE), 500VAC (Secondary-PE)
Insulation Resistance>5MΩ at 500VDC (between all I/O points and ground)
Noise ImmunityESD (IEC 61131-2, IEC 61000-4-2): 8kV Air Discharge
EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2kV, Digital I/O: 1kV, Analog & Communication I/O: 1kV
RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m
GroundingThe diameter of grounding wire shall not be less than that of L, N terminal of the power supply.
(When many PLCs are in use at the same time, please make sure every PLC is properly grounded.)
EnvironmentOperation: 0°C~55°C (temperature), 5~95% (humidity), pollution degree 2
Storage: -25°C~70°C (temperature), 5~95% (humidity)
ApprovalsUL508, European community EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC
Vibration/Shock ImmunityInternational standards: IEC61131-2, IEC 68-2-6 (TEST Fc)/ IEC61131-2 & IEC 68-2-27 (TEST Ea)
RS485 Port10/14 I/O models do not support RS485, other models is available
WeightSee below "Selection Table"
Note:
*1. It is suggested that the power output should not be supplied to HMIs.

Selection Table

ModelBuilit-in I/ONumber of Inputs
Number of Outputs
Output Type
COM PortWeight
DVP10EC00R31064RelayRS-232205g
DVP10EC00T31064TransistorRS-232192g
DVP14EC00R31486RelayRS-232210g
DVP14EC00T31486TransistorRS-232195g
DVP16EC00R31688RelayRS-232/RS-485220g
DVP16EC00T31688TransistorRS-232/RS-485198g
DVP20EC00R320128RelayRS-232/RS-485310g
DVP20EC00T320128TransistorRS-232/RS-485285g
DVP24EC00R3241212RelayRS-232/RS-485322g
DVP24EC00T3241212TransistorRS-232/RS-485288g
DVP30EC00R3301812RelayRS-232/RS-485325g
DVP30EC00T3301812TransistorRS-232/RS-485290g
DVP32EC00R3321616RelayRS-232/RS-485340g
DVP32EC00T3321616TransistorRS-232/RS-485295g
DVP40EC00R3402416RelayRS-232/RS-485380g
DVP40EC00T3402416TransistorRS-232/RS-485340g
DVP48EC00R3482820RelayRS-232/RS-485540g
DVP48EC00T3482820TransistorRS-232/RS-485505g
DVP60EC00R3603624RelayRS-232/RS-485560g
DVP60EC00T3603624TransistorRS-232/RS-485510g

PLC I/O Point Specification

Input Points
Input Point No.X0 ~ X3X4 ~ X17X20 ~  #1
Input Point TypeDigital input
Input FormDC (SINK or SOURCE)
Input Currrent24VDC, 5mA
Max. Input Frequency20kHz10kHz60Hz
Action LevelOff → On>15VDC
On → Off< 5VDC
Response TimeOff → On< 25μs< 50μs< 10ms
On → Off< 10μs< 20μs< 15ms
Filter TimeX0 ~ X17Approx. 10ms (0~20ms adjustable in D1020, D1021)
Output Points
Output Point TypeRelay - RTransistor - T
Voltage Specification< 240VAC, 30VDC5 ~ 30VDC #2
Max. Output Frequency1HzNormal inputs10kHz #4
Maximum LoadResistive2A/point (5A/COM)0.5A/1 point (4A/ZP)
Inductive#315W (30VDC)
Lamp20W DC/100W AC2.5W (30VDC)
Response TimeOff → OnApprox. 10ms< 30μs< 20μs
On → Off< 350μs< 50μs
Note:
#1. Please refer to “I/O Terminal Layouts” for the max. X/Y No. on each model.
#2. UP, ZP must work with external auxiliary power supply 24V DC (-15% ~ +20%), rated consumption approx. 1mA/point.
#3. Life curves
PLC Controller Life Curve
#4. The maximum frequency is applicable to Y0-Y3 in all DVP-EC3 series PLCs, and other output terminals are general terminals.

Dimensions

EC3 Series Programmable Logic Controller Dimensions

Model10EC00R/T314EC00R/T316EC00R/T320EC00R/T324EC00R/T330EC00R/T332EC00R/T340EC00R/T348EC00R/T360EC00R/T3
L95150164240
L186141155231

Product reviews
PLC controller controls smoothly
5
Rogers
Avatar
3/16/2021 12:48 AM
I am using a PLC controller to control the speed and simple communication monitoring. The PLC controller runs and controls very smoothly, and I strongly recommend it to friends around me.
Was this review helpful? Yes No (0/0)
great little plc controller
4
Becky11
Avatar
10/10/2025 8:42 PM
I'm really impressed with the overall value of this PLC controller. It was easy to set up for a basic automation job and the built-in communication ports are a huge plus. My only small complaint is that the documentation could be a bit clearer in a few spots. But for the cost, it's a reliable workhorse.
Was this review helpful? Yes No (0/0)
Just installed this PLC to automate our packaging line
5
Joey
Avatar
10/19/2025 9:38 PM
It handles all our sensors and solenoids perfectly. Programming was straightforward with the free software, and the relay outputs directly control our motors. After running 24/7 for two months, no issues. It's much more reliable than the old timer relays we used before.
Was this review helpful? Yes No (0/0)
It's a practical choice for simple control tasks
5
Thomas
Avatar
10/29/2025 11:55 PM
I’ve been using this PLC for a few months now, and it’s been surprisingly solid. Setup was straightforward, and it runs my small automation setup without a hitch. The relay outputs respond quickly, and the build feels durable.
Was this review helpful? Yes No (0/0)
Only registered users can write reviews
Customers who bought this item also bought

Programmable Timer Relay, 8-Input 8-Output, 12V/24V DC

ATO-TIMER-16PLC
$127.65
8-input 8-output programmable timer relay, with 12V or 24V DC supply voltage, can work as simple PLC, with intelligent and humanized control, easy to learn, understand and operate. Optional 3 output forms of transistor DC output, transistor AC output and relay output. Input compatible with PNP/NPN. High reliability and competitive price.