Boasting a high resolution of 0.1dB, with a remarkable accuracy of ±1.5dB, noise detection sensor delivers precise data for detailed analysis and monitoring.
Specification
| Model | ATO-YS19 | ATO-YS20 | |
| Interface Method | 0-5V | 0-10V | 4-20mA |
| Operating Voltage | 12-25VDC | 13-25VDC | |
| Operating Current | 23mA(@24.0V) | 28mA(@24.0V) | |
| Measurement Range | 30-130dB | ||
| Frequency Range | 31.5 -8kHz | ||
| Weighting Method | A-weighting | ||
| Resolution (of a Photo) | 0.1dB | ||
| Accurate | ±1.5dB | ||
| Response Time | 100ms, 250ms, 300ms, 400ms (Factory Default 400ms) | ||
| Operating Temperature | -20℃~60℃ | ||
| Overall Dimension | 110 (Length) × 20 (Diameter) mm | ||
| Protocol mode | Analogue | ||
Feature
- L-shaped bracket and double nuts: Easy to install and remove, more convenient construction.
- Precision dual X-layer board design: Professional noise processing chip, processing weighting network, designing filter network, mourning and RMS operation circuit, and on-board calibration potentiometer. On-board TVS, ESD and self-recovery fuse protection devices to increase circuit reliability.
- Stainless steel tube body: Adopting 304 stainless steel to make the tube body, with strong, rust-resistant and high-temperature-resistant features.
- Stainless steel waterproof sealing connector: It can cope with the complex outdoor environment and realise waterproof and moisture-proof function.
- 1 metre four core cable: 0.5 flat core, easy wiring, more stable communication
Dimension


Wiring Description
The three-wire method is used, and the specific wire sequence is shown in the table below:
| Blue | Yellowish Green | Brown |
| VCC | GND | Signal Output |
Tips: Is the Noise sensor compatible with common data acquisition systems?
To determine the compatibility of the noise sensor with common data acquisition systems, you should refer to the sensor's technical specifications or documentation. Look for information related to communication protocols and output signals. Common data acquisition systems typically support various analog signals.
- Check the Datasheet: Look for a datasheet or technical documentation that comes with the noise sensor. It should provide details on the electrical outputs and communication protocols.
- Analog Output Compatibility: Confirm that the voltage outputs (0-5V, 0-10V) and current output (4-20mA) are within the input range of your data acquisition system. Most systems are versatile and can handle a variety of analog signals.
- Communication Protocols: Check if the noise sensor uses standard communication protocols such as voltage signals or current loops. Common data acquisition systems often support widely used protocols.
- Voltage/Current Input of Data Acquisition System: Ensure that the data acquisition system you plan to use has input channels that match the voltage and current specifications of the noise sensor. For example, if the sensor outputs a 0-5V signal, make sure the data acquisition system has input channels designed for that range.
- Signal Conditioning Requirements: Some sensors may require signal conditioning or amplification. Check if the noise sensor needs any specific signal conditioning and whether your data acquisition system can provide it if necessary.
- Compatibility with Software: Verify if the software used by your data acquisition system supports the type of signal and units provided by the noise sensor. This is important for accurate data interpretation and analysis.
Product reviews
Practical noise monitoring tool
Sawyer
4/16/2025 8:45 PM
This noise sensor is very practical, the device is responsive, the data reading is intuitive and clear, and the installation is also simple. Overall, it is cost-effective and has stable performance. It is a product worth buying.
Was this review helpful? (0/0)
About Noise Sensor
Salillo
7/28/2025 9:17 PM
I am looking for a 2-wire noise sensor with 4-20mA output, but the product description shows 3 wires. Is that right?
Was this review helpful? (0/0)
Sensor Pitch
Obinna
1/27/2026 11:18 PM
Yes, I'm looking for the pitch of the threaded cylinder body of this noise sensor. I know it's 20mm, but what is the pitch?
Was this review helpful? (0/0)
Two Questions
Fendios
4/14/2026 2:54 AM
Regarding the ATO-YS19 sensor, I have two questions:
1) Does this sensor provide a 0–10V output signal?
2) Can you provide the Declaration of Conformity for this sensor?
1) Does this sensor provide a 0–10V output signal?
2) Can you provide the Declaration of Conformity for this sensor?
Was this review helpful? (0/0)
A few questions
Portus
9/14/2026 12:46 AM
I have a few questions: 1. What is the calibration/maintenance cycle? If calibration is required, do I need to purchase any equipment? 2. What is the service life of this sensor?
Was this review helpful? (0/0)
Only registered users can write reviews
Customers who bought this item also bought
DC-DC Boost Converter, 12V to 24V
ATO-DCDC-1224
$53.26
High quality and cost-effective DC-DC boost converter series step up 12V DC to 24V DC, power rating from 24 watts to 1200 watts, 10-23V DC input range. 100% waterproof & anti-shock protection, ultra compact size, light weight.
Digital Rotary Torque Sensor, 0.1/5/300/1000 Nm to 10000 Nm
ATO-TQS-D03
$939.15
Digital rotary torque sensor with LCD display has the capacity range from 0.1 Nm/0.3 Nm/1 Nm/5 Nm/10 Nm/300 Nm/1000 Nm to 10000 Nm. LCD display can show torque, speed and power value at the same time. Dynamic torque sensor adopts two NSK shafts to ensure starting torque as low as 0.00001 Nm. Rotary torque transducer with 7 pin waterproof circular connector and 3m cable can measure both forward and reverse torque, and then output ±5V/0-10V/4-20mA/RS485 torque signal to PLC.
Industrial Vibration Sensor, RS485/4-20mA/0-5V/0-10V
ATO-VT-N01
$139.66
Good quality industrial vibration sensors for sale support RS485/4-20mA/0-5V/0-10V and other transmission modes to meet different site monitoring needs. This vibration transmitter can detect 10-1600Hz/10-5000Hz frequency range of uniaxial/triaxial vibration displacement, suitable for all kinds of motors, fans, pumps, machine tools and other equipment vibration testing and fault reduction.
Oxygen Gas Sensor/Transmitter, RS485/4-20mA/0-5V
ATO-GS-O2-3002
$101.58
The oxygen gas sensor measures ranges of 0-30%VOL for RS485 output and 0-25%VOL for analog output, with an accuracy of ±3%FS and a resolution of 0.1%VOL. Gas transmitter has a power supply range of 10~30V DC, with the 0~10V output type requiring a 24V supply. Widely used in industries such as process control, environmental monitoring, medical devices, food and beverage, safety detection, scientific research, and combustion system optimization.
Digital Pressure Sensor for Hydraulic/Steam/Air
ATO-PRES-PX300
$173.33
Digital pressure sensor covers -0.1 to 100 MPa and supports 4–20mA, 0–20mA, voltage and RS485 outputs, with a backlit LCD display. Suitable for hydraulic, steam, air and liquid pressure measurement, with medium temperatures from -40°C to 60°C.