Miniature Compression Load Cell 5kg/10kg/30kg/50kg/100kg

$134.39
Compression load cell has a capacity range from 5kg, 10kg, 20kg, 30kg, 50kg to 100kg. It has a button type structure, miniature diameter 13mm and height 7mm, cable Φ2*2m. Compression load cell can be used in pressure testers, automotive installation, automated assembly line, robotics, etc.
SKU: ATO-LC-BU03
*
*
*
Free Shipping
Delivery date: 6-12 days

After purchasing one ATO load cell, you can buy a special digital panel meter to obtain readings directly, or buy a transmitter to output standard signal to PLC, DCS and other systems. Customized output signal is 0-5V, 0-10V, or 4-20mA.

Note: The load cell cannot be connected to both the transmitter and the controller at the same time — only one can be selected.

The miniature button cload cell is a high-precision measuring device that can measure very small changes in weight or pressure. When an external force acts on the sensor, the metal structure will undergo slight deformation, which will cause the strain gauge to output a weak electrical signal. This electrical signal is then amplified, filtered and analyzed by a data acquisition system, and ultimately converted into a readable numerical or graphical display.

Miniature compression load cells have capacity range from 5kg, 10kg, 20kg, 30kg, 50kg to 100kg. Load cell capacity can be customized according to customer requirements.

Specification

ModelATO-LCBU-DYHW-113
Shipping Weight1kg
Capacity Range *0~100kg
Matched Display ControllerATO-DPM-DY800 (Click it to the transmitter page)
Matched TransmitterATO-LCTR-OA (Click it to the transmitter page)
Accuracy0.5%F.S (linearity + hysteresis + repeatability)
Sensitivity2.0±10%mV/V (Low range variations may differ)
Creep±0.1%F.S/30min
Zero Output±2%F.S
Temperature Effect on Zero±0.2%F.S/10℃
Temperature Effect on Output±0.2%F.S/10℃
Operating Temperature-20℃~+80℃
Input Impedance500Ω
Output Impedance1000Ω
Insulation Resistance≥5000MΩ
Safety Overload150%F.S
Bridge Voltage (excitation voltage)DC 5-10V
MaterialStainless steel
Protection ClassIP66
Cable Length2m
WiringEXC+: Red, EXC-: Black, SIG+: Green, SIG-: White


Feature

Miniature compression load cell 5kg to 100kg feature

  • High-Quality 17-4PH Stainless Steel Construction: Provides stable and durable structure with excellent resistance to corrosion and high mechanical strength.
  • High Accuracy and Stability: Designed for precise measurements with high accuracy, ensuring stable performance over time.
  • Pressure Resistance and Small Size: Can withstand significant pressure while maintaining a compact size for easy integration into various applications.
  • 2-Meter Long External Cables: Comes with a 2-meter cable for convenient installation and flexibility in placement.
  • Long-Term Stability and Durability: Built for long-term use with strong anti-interference and high durability, ensuring reliable performance in demanding environments.
  • High Precision Sensing Element: Features a high-precision sensing element with good resistance to heat and temperature changes, maintaining accuracy over extended periods.

Miniature compression load cell dimension (unit: mm)

CapacityDimension (mm)
Φ
5~20kg2
30~100kg3

Miniature compression load cell 5kg/10kg/30kg/50kg/100kg dimension

Wiring Method

Load cell wiring method

Application

Miniature compression load cell 5kg to 100kg application

Tips: What is a Miniature Compression Load Cell?

A Miniature Compression Load Cell is a compact and precise force measurement device designed to measure compressive forces in small spaces. It works by converting mechanical force (such as compression) into an electrical signal that can be measured. These load cells are ideal for applications where space is limited, but accurate force measurements are still necessary.

In this video, ATO will show you how to wire a strain gauge load cell with a display controller.

Low Profile Micro Compression Button Load Cell 100kg
This video introduces the specs, design features and applications of a low profile miniature button load cell DYHW-110 that's intended for compression force measurement. The maximum load capacity it can bear is 100kg. It can achieve 0.5%F.S accuracy with 150%F.S safety overload and temperature compensation.

Shear Beam Load Cell | Single & Double-Ended, Weighbridge Load Cells

The shear beam load cell is a common load cell. Its working principle is based on the deformation of the elastomer when it is acted upon by an external force. This deformation will cause the resistance of the elastomer to change, thereby achieving the measurement of the external force. It is typically used to measure forces in the small to medium range and its working principle is based on the shear effect of elastically deforming materials. This type of force measuring element is usually made of metal or polymer materials. Because of its high elastic modulus and shear modulus, it can produce stable shear deformation when subjected to external forces.

How to Ensure the Accuracy of Your Weighing System?

This video describes five factors that affect the accuracy of a weighing system and provides recommendations for selecting, installing, and operating the system to handle these factors.

Load Cell Transmitter 4~20mA Output Calibration

This video demonstrates how to calibrate the 4~20mA output. The 0~10V is also calibrated in the same way.

How Does PLC Read Data of Load Cell Transmitter?

In this video, it shows how PLC reads data from sensor transmitter. This system mainly consists of PLC, ATO load cell transmitter, ATO load cell, 24VDC power supply, personal computer, etc.

Product reviews
Unit of miniature compression load cell
5
Denise
Avatar
4/20/2021 9:51 PM
I want to buy a load cell controller, but needs to get weight in ton not kg, is it possible?
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, it possible. You can use the controller to measure tons unit. There are 4 options for unit setting (0=ton, 1=kg, 2=g, 3=kn).
Selection of miniature compression load cell
5
Branco
Avatar
5/27/2021 1:11 AM
Does the "load cell transmitter, output 0-5V/0-10V/4-20mA/0-20mA" output, so I can choose in site?
Was this review helpful? Yes No (0/0)
ATO Responded
You can choose while ordering which output signale you will be needing not on site, it should be one value "factory selected option".
Does the load cell need to be calibrated?
5
Jfinva
Avatar
5/30/2021 9:37 PM
If the load cell permanently mounted. Does it need to be calibrated once in while because of the creep?
Was this review helpful? Yes No (0/0)
ATO Responded
When sensor reading has a large error (measured value is not accurate), the calibration is required, but calibration is not determined according to usage time.
Information about the miniature compression load cell
5
Utkarsh
Avatar
6/2/2021 9:57 PM
What happens if the load exceeds 100%F.S? For example, can I operate the load cell at 125%F.S? Or 150%?
Was this review helpful? Yes No (0/0)
ATO Responded
Within 150% of the range, the components inside the sensor may be damaged, and more than 150% of the sensor capacity, may cause deformation.
Wire diameter size
5
Reland
Avatar
8/10/2025 8:40 PM
Hello, what is the wire diameter for the ATO-LC-BU03?
Was this review helpful? Yes No (0/0)
ATO Responded
Regarding the wire diameter of this sensor, the 5-20 kg range is 2 mm, and the 30-200 kg range is 3 mm.
Some questions
4
Kiko
Avatar
7/31/2026 1:39 AM
Product: ATO-LC-BU03
Please confirm: Individual repeatability specifications (separate from the 0.5% full-scale composite value); A/D conversion rate (Hz) of the DY800 display controller; Relay output response time (ms) and contact type (dry contact/NPN/PNP); RS485 update rate and whether it supports continuous data stream mode; Is this controller compatible with the 1000Ω output impedance of this load cell?
Was this review helpful? Yes No (0/0)
ATO Responded
1. The load cell repeatability is 0.3% F.S., 1000Ω, and the output impedance is compatible with the display controller.
2. The DY800 display controller has a measurement speed of 5-200Hz, a communication rate of 2400~256000, and an RS485 RTU command transmission interval of 50 milliseconds or more.
3. The relay has a normally open dry contact output; response time data will be available after ordering and testing.
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

After purchasing one ATO load cell, you can buy a special digital panel meter to obtain readings directly, or buy a transmitter to output standard signal to PLC, DCS and other systems. Customized output signal is 0-5V, 0-10V, or 4-20mA.

Note: The load cell cannot be connected to both the transmitter and the controller at the same time — only one can be selected.

The miniature button cload cell is a high-precision measuring device that can measure very small changes in weight or pressure. When an external force acts on the sensor, the metal structure will undergo slight deformation, which will cause the strain gauge to output a weak electrical signal. This electrical signal is then amplified, filtered and analyzed by a data acquisition system, and ultimately converted into a readable numerical or graphical display.

Miniature compression load cells have capacity range from 5kg, 10kg, 20kg, 30kg, 50kg to 100kg. Load cell capacity can be customized according to customer requirements.

Specification

ModelATO-LCBU-DYHW-113
Shipping Weight1kg
Capacity Range *0~100kg
Matched Display ControllerATO-DPM-DY800 (Click it to the transmitter page)
Matched TransmitterATO-LCTR-OA (Click it to the transmitter page)
Accuracy0.5%F.S (linearity + hysteresis + repeatability)
Sensitivity2.0±10%mV/V (Low range variations may differ)
Creep±0.1%F.S/30min
Zero Output±2%F.S
Temperature Effect on Zero±0.2%F.S/10℃
Temperature Effect on Output±0.2%F.S/10℃
Operating Temperature-20℃~+80℃
Input Impedance500Ω
Output Impedance1000Ω
Insulation Resistance≥5000MΩ
Safety Overload150%F.S
Bridge Voltage (excitation voltage)DC 5-10V
MaterialStainless steel
Protection ClassIP66
Cable Length2m
WiringEXC+: Red, EXC-: Black, SIG+: Green, SIG-: White


Feature

Miniature compression load cell 5kg to 100kg feature

  • High-Quality 17-4PH Stainless Steel Construction: Provides stable and durable structure with excellent resistance to corrosion and high mechanical strength.
  • High Accuracy and Stability: Designed for precise measurements with high accuracy, ensuring stable performance over time.
  • Pressure Resistance and Small Size: Can withstand significant pressure while maintaining a compact size for easy integration into various applications.
  • 2-Meter Long External Cables: Comes with a 2-meter cable for convenient installation and flexibility in placement.
  • Long-Term Stability and Durability: Built for long-term use with strong anti-interference and high durability, ensuring reliable performance in demanding environments.
  • High Precision Sensing Element: Features a high-precision sensing element with good resistance to heat and temperature changes, maintaining accuracy over extended periods.

Miniature compression load cell dimension (unit: mm)

CapacityDimension (mm)
Φ
5~20kg2
30~100kg3

Miniature compression load cell 5kg/10kg/30kg/50kg/100kg dimension

Wiring Method

Load cell wiring method

Application

Miniature compression load cell 5kg to 100kg application

Tips: What is a Miniature Compression Load Cell?

A Miniature Compression Load Cell is a compact and precise force measurement device designed to measure compressive forces in small spaces. It works by converting mechanical force (such as compression) into an electrical signal that can be measured. These load cells are ideal for applications where space is limited, but accurate force measurements are still necessary.

Product reviews
Unit of miniature compression load cell
5
Denise
Avatar
4/20/2021 9:51 PM
I want to buy a load cell controller, but needs to get weight in ton not kg, is it possible?
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, it possible. You can use the controller to measure tons unit. There are 4 options for unit setting (0=ton, 1=kg, 2=g, 3=kn).
Selection of miniature compression load cell
5
Branco
Avatar
5/27/2021 1:11 AM
Does the "load cell transmitter, output 0-5V/0-10V/4-20mA/0-20mA" output, so I can choose in site?
Was this review helpful? Yes No (0/0)
ATO Responded
You can choose while ordering which output signale you will be needing not on site, it should be one value "factory selected option".
Does the load cell need to be calibrated?
5
Jfinva
Avatar
5/30/2021 9:37 PM
If the load cell permanently mounted. Does it need to be calibrated once in while because of the creep?
Was this review helpful? Yes No (0/0)
ATO Responded
When sensor reading has a large error (measured value is not accurate), the calibration is required, but calibration is not determined according to usage time.
Information about the miniature compression load cell
5
Utkarsh
Avatar
6/2/2021 9:57 PM
What happens if the load exceeds 100%F.S? For example, can I operate the load cell at 125%F.S? Or 150%?
Was this review helpful? Yes No (0/0)
ATO Responded
Within 150% of the range, the components inside the sensor may be damaged, and more than 150% of the sensor capacity, may cause deformation.
Wire diameter size
5
Reland
Avatar
8/10/2025 8:40 PM
Hello, what is the wire diameter for the ATO-LC-BU03?
Was this review helpful? Yes No (0/0)
ATO Responded
Regarding the wire diameter of this sensor, the 5-20 kg range is 2 mm, and the 30-200 kg range is 3 mm.
Some questions
4
Kiko
Avatar
7/31/2026 1:39 AM
Product: ATO-LC-BU03
Please confirm: Individual repeatability specifications (separate from the 0.5% full-scale composite value); A/D conversion rate (Hz) of the DY800 display controller; Relay output response time (ms) and contact type (dry contact/NPN/PNP); RS485 update rate and whether it supports continuous data stream mode; Is this controller compatible with the 1000Ω output impedance of this load cell?
Was this review helpful? Yes No (0/0)
ATO Responded
1. The load cell repeatability is 0.3% F.S., 1000Ω, and the output impedance is compatible with the display controller.
2. The DY800 display controller has a measurement speed of 5-200Hz, a communication rate of 2400~256000, and an RS485 RTU command transmission interval of 50 milliseconds or more.
3. The relay has a normally open dry contact output; response time data will be available after ordering and testing.
Only registered users can write reviews
Customers who bought this item also bought

Digital Load Cell Amplifier, Output 4-20mA/0-10V/RS485

ATO-LCTR-OAR
$109.85
High precision load cell amplifier has a 6 digit LED display, output signal 4-20mA/ 0-5V/ 0-10V/ RS485. There are 3 keys for parameter settings. Digital load cell amplifier can be calibrated on-line by its 3 keys. The setting parameters include zero, capacity, communication rate, division value, decimal digits, etc.