470μF 25V SMD Electrolytic Capacitor

$1.61
470μF SMD aluminum electrolytic capacitor with 25 volt rated voltage. Lower cost SMD aluminum electrolytic capacitori with surface mount installation type, ±20% cap. tolerance. SMD non polarized capacitor usually play the electrical functions of filtering, bypassing, coupling, decoupling, and switching.
SKU: ATO-EC-S470UF25V
This product has a minimum quantity of 500
Free Shipping
Delivery date: 6-12 days

Cheap price SMD electrolytic capacitor featuring 470μF capacity, 2000h endurance, 18% dissipation factor, -55~105℃ operating temperature. Surface mount electrolytic capacitor are used in various electronic products with compact structure, small volume and high precision.

Features

  • Endurance: 105℃ - 2000 hours
  • Low ESR and high ripple current
  • Vibration-proof (vP) version (up to 30g) available upon request
  • AEC-Q200 version available
  • High voltage, automotive 105°C type

Specification

ModelATO-EC-HV471M025G
Capacity470㎌
Rated voltage25V
Size10*10.5mm
Installation typeSurface mount
Operating temperature-55~105℃
Cap. tolerance (∆C)±20% (120Hz 20℃)
Dissipation factor (tanδ)18%
Low temperature characteristic at 120Hz (Z ratio max.)3 (Z-25℃/Z+20℃)
Leakage current (Lleak)≤0.01*CR*VR or 3 ㎂ * after 2 minutes
Enduarance (105℃)Test2000h
∆C≤20% of initial measured value
tanδ≤200% of specified measured value
Lleak≤ the specified measured value
Shelf life (105℃)Test1000h
∆C≤20% of initial measured value
tanδ≤200% of specified measured value
Lleak≤ the specified measured value
Resistance to soldering heat (105℃)∆CWithin ±10% of initial value
tanδLess than specified value
LleakLess than specified value

Dimension (mm)

SMD electrolytic capacitor dimension

ModelDimension (mm)
ATO-EC-HV471M025G∅D10
L10.5
aMax
A10.3
B10.3
C11
W0.7~1.1
P±24.5

Tips:  How to make a SMD Electrolytic Capacitor?

  1. Impregnation of the electrolyte.
    After the electrolytic paper is wound, the electrolyte is poured into it so that the electrolyte is impregnated on the electrolytic paper. With the improvement of electrolyte formula and the improvement of electrolytic paper manufacturing technology, the ESR value of aluminum electrolyte capacitors has gradually increased, becoming a fraction of the previous one.
  2. Assembly.
    This step is to assemble the aluminum shell on the outside of the capacitor and connect the outer leads at the same time. The capacitor has been basically formed at this time.
  3. Crimping.
    If the SMD aluminum electrolytic capacitor is the kind of "wrapped" capacitor, you need to go through this step and put the PVC film covering the capacitor on the outside of the capacitor's aluminum shell. However, there are fewer and fewer capacitors using PVC film today. The main reason is that this material does not conform to the trend of environmental protection, and has little to do with performance.

In this video, ATO will show you three phase parallel capacitors / self-healing.

Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

Cheap price SMD electrolytic capacitor featuring 470μF capacity, 2000h endurance, 18% dissipation factor, -55~105℃ operating temperature. Surface mount electrolytic capacitor are used in various electronic products with compact structure, small volume and high precision.

Features

  • Endurance: 105℃ - 2000 hours
  • Low ESR and high ripple current
  • Vibration-proof (vP) version (up to 30g) available upon request
  • AEC-Q200 version available
  • High voltage, automotive 105°C type

Specification

ModelATO-EC-HV471M025G
Capacity470㎌
Rated voltage25V
Size10*10.5mm
Installation typeSurface mount
Operating temperature-55~105℃
Cap. tolerance (∆C)±20% (120Hz 20℃)
Dissipation factor (tanδ)18%
Low temperature characteristic at 120Hz (Z ratio max.)3 (Z-25℃/Z+20℃)
Leakage current (Lleak)≤0.01*CR*VR or 3 ㎂ * after 2 minutes
Enduarance (105℃)Test2000h
∆C≤20% of initial measured value
tanδ≤200% of specified measured value
Lleak≤ the specified measured value
Shelf life (105℃)Test1000h
∆C≤20% of initial measured value
tanδ≤200% of specified measured value
Lleak≤ the specified measured value
Resistance to soldering heat (105℃)∆CWithin ±10% of initial value
tanδLess than specified value
LleakLess than specified value

Dimension (mm)

SMD electrolytic capacitor dimension

ModelDimension (mm)
ATO-EC-HV471M025G∅D10
L10.5
aMax
A10.3
B10.3
C11
W0.7~1.1
P±24.5

Tips:  How to make a SMD Electrolytic Capacitor?

  1. Impregnation of the electrolyte.
    After the electrolytic paper is wound, the electrolyte is poured into it so that the electrolyte is impregnated on the electrolytic paper. With the improvement of electrolyte formula and the improvement of electrolytic paper manufacturing technology, the ESR value of aluminum electrolyte capacitors has gradually increased, becoming a fraction of the previous one.
  2. Assembly.
    This step is to assemble the aluminum shell on the outside of the capacitor and connect the outer leads at the same time. The capacitor has been basically formed at this time.
  3. Crimping.
    If the SMD aluminum electrolytic capacitor is the kind of "wrapped" capacitor, you need to go through this step and put the PVC film covering the capacitor on the outside of the capacitor's aluminum shell. However, there are fewer and fewer capacitors using PVC film today. The main reason is that this material does not conform to the trend of environmental protection, and has little to do with performance.
Only registered users can write reviews