Closed Loop Stepper Motor Driver, 2 Phase, 1A ~ 6A

$103.89
Closed loop stepper driver is used for Nema 23 2 phase closed loop stepper motor. This controller can be equipped with an encoder to transform pulse signal into angular displacement signal. Work at DC 24V ~ 50V, drive current 1A ~ 6A.
SKU: ATO-STEP-B506T
*
Free Shipping
Delivery date: 6-12 days

Low price closed loop stepper driver is an actuator which used for Nema 17 bipolar stepper motor. It drives hybrid 2 phase stepper motor to rotate at a step angle in the set direction when receiving a pulse signal.

Features

  • High performance and high efficiency. The digital stepper motor driver adopts 32-bit DSP control technology to make the hybrid bipolar stepper motor achieve the best output performance.
  • Low vibration and low noise. The method of combining digital and analog and advanced closed-loop control system of power angle.
  • Small temperature rise and long life. The current is adjusted intelligently according to the load.
  • Interference frequency filtering. Photoelectric isolation differential signal input, impulse response frequency up to 200Kpps.
  • Strong function and low repair rate. Under-voltage, over-voltage, over-current, short circuit, open circuit, tracking error out of tolerance and other fault diagnosis transition indication and automatic protection function.

Specification

ModelATO-FYDB506T
Matched MotorNema 23 2 Phase Closed Loop Stepper Motor
VoltageDC 24V ~ 50V
Drive Current1.0A ~ 6.0A Auto-Adjust
Microstepping Setting25600 steps/rev 16 Channels
Hightest Pulse Frequency200Kpps
CertificationCE, FCC, RoHS
Dimensions116 x 70 x 26.5mm
Weight0.5kg
Function Description
FunctionsOperation Instructions
PWRPower Indicating LampWhen the driver is powered on, the green light is always on.
ALARMOvercurrent/Undervoltage IndicatorWhen the overvoltage and overcurrent faults occur, the red light is always on.
PUL+Positive End of Control Pulse SignalConnect to signal power,+5V to +24V can be driven.
PUL-Negative End of Control Pulse SignalThe falling edge is valid, and the motor takes one step whenever the pulse changes from high to low. Input resistance 220Ω. Requirements: low level 0 to 0.5V, high level 4 to 5V, Pulse charge >2.5us.
DIR+Positive End of Directional SignalConnect to signal power,+5V to +24V can be driven.
DIR-Negative End of Directional SignalUsed to change the direction of the motor. Input resistance 220Ω. Requirements: low level 0 to 0.5V, high level 4 to 5V, Pulse charge >2.5us.
ENA+Positive End of Enabling SignalConnect to signal power,+5V to +24V can be driven.
ENA-Negative End of Enabling SignalWhen it is valid (low level), the motor coil current is turned off, the driver stops working, and the motor is in a free state.
ALM+Positive End of Alarm Signal OutputWhen over-current, over-voltage, under-voltage or over-tolerance alarms, the alarm signal is valid (the output photocoupler is turned on). ALM+ is connected to the pull-up power to use the positive pole of the output power supply, and ALM- is connected to the negative pole of the output power supply. Maximum drive current 50mA.
ALM-Negative End of Alarm Signal Output
EZ+/EZ-Positive/Negative End of Encoder Z Phase InputPositive input/negative input of Connecting to encoder Z channel
EB+/EB-Positive/Negative End of Encoder B Phase InputPositive input/negative input of Connecting to encoder B channel
EA+/EA-Positive/Negative End of Encoder A Phase InputPositive input/negative input of Connecting to encoder A channel
VCCEncoder Power Supply5V encoder power supply
GNDGround of Encoder Power SupplyGround of Encoder Power Supply
A+A-Motor WiringFour lead wires
B+B-

Microstep Segmentation Setting

Pulse/RevoSW1SW2SW3SW4
Defaultonononon
800offononon
1600onoffonon
3200offoffonon
6400ononoffon
12800offonoffon
25600onoffoffon
500offoffoffon
1000onononoff
2000offononoff
4000onoffonoff
5000offoffonoff
8000ononoffoff
10000offonoffoff
3600onoffoffoff
7200offoffoffoff

Dimensions (Unit: mm)

Dimensions of 1A to 6A Digital Closed Loop Stepper Motor Driver

Wiring Diagram

Wiring Diagram of 1A to 6A Digital Closed Loop Stepper Motor Driver

Details

1A~6A Closed Loop Stepper Motor Driver Details

Tips: How to set up a 2 phase stepper motor driver

Usually the step angle of a two-phase stepper motor is 1.8 degrees. It is calculated that it takes 200 pulses to make one revolution, that is, it needs to walk 200 steps, and each step is 1.8 degrees. Generally, two phase hybrid stepper motor drivers are equipped with switches to adjust the number of subdivisions. You can easily set the desired number of subdivisions by flipping the corresponding setting switch against the setting table.

Two phase bipolar stepper motor driver setting table has two forms, one is the subdivision number, and the other is to directly give the number of pulses required for each revolution under different subdivision numbers. In order to adapt to stepping motors with different rated currents, the drive generally has an adjustment function, and the adjustment method is also different. Generally, two forms of potentiometer or dial switch are used. The most commonly used is the dial switch form. Appropriate current parameters should be selected when setting, the greater the current, the greater the torque that the motor can generate.

In order to reduce the heating of the motor, many drivers have a half-current function. When the half-current switch is turned on, the stepper motor driver will reduce the current to the set value if it does not receive a pulse signal within a short period of time. Half, let the motor better heat dissipation. But when this function is used, the locking torque will be reduced correspondingly in the half-flow state, so it needs to be selected according to actual needs.

How to control a stepper motor using a PLC and HMI?
This video shows you how to configure a PLC, HMI, motor driver, and proximity sensor to perform Origin Return (OPR) control of a stepper motor.

Common Stepper Motor Troubleshooting Problems and Tips
In this video, 9 common problems that can occur with stepper motors are discussed, and expert advice is provided for diagnosing and effectively resolving these problems. If you have ever experienced problems with your stepper motor or want to be prepared for any future problems, this video is a must watch.

Product reviews
I really recommend everyone to buy
5
Dpolister
Avatar
12/8/2021 6:25 PM
This 2 phase closed loop stepper motor driver is super affordable, good quality and low price. I just bought it and used it. Generally speaking, I am very satisfied with it. I sincerely recommend everyone to buy, don't worry about quality problems.
Was this review helpful? Yes No (0/0)
Overall performance is good and meets my expectations
4
Gavin
Avatar
12/8/2025 12:59 AM
Stable performance, low noise, and fast response. The auto current adjustment is hassle-free, and the full protection features make the motor run smoothly and reliably.
Was this review helpful? Yes No (0/0)
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

Low price closed loop stepper driver is an actuator which used for Nema 17 bipolar stepper motor. It drives hybrid 2 phase stepper motor to rotate at a step angle in the set direction when receiving a pulse signal.

Features

  • High performance and high efficiency. The digital stepper motor driver adopts 32-bit DSP control technology to make the hybrid bipolar stepper motor achieve the best output performance.
  • Low vibration and low noise. The method of combining digital and analog and advanced closed-loop control system of power angle.
  • Small temperature rise and long life. The current is adjusted intelligently according to the load.
  • Interference frequency filtering. Photoelectric isolation differential signal input, impulse response frequency up to 200Kpps.
  • Strong function and low repair rate. Under-voltage, over-voltage, over-current, short circuit, open circuit, tracking error out of tolerance and other fault diagnosis transition indication and automatic protection function.

Specification

ModelATO-FYDB506T
Matched MotorNema 23 2 Phase Closed Loop Stepper Motor
VoltageDC 24V ~ 50V
Drive Current1.0A ~ 6.0A Auto-Adjust
Microstepping Setting25600 steps/rev 16 Channels
Hightest Pulse Frequency200Kpps
CertificationCE, FCC, RoHS
Dimensions116 x 70 x 26.5mm
Weight0.5kg
Function Description
FunctionsOperation Instructions
PWRPower Indicating LampWhen the driver is powered on, the green light is always on.
ALARMOvercurrent/Undervoltage IndicatorWhen the overvoltage and overcurrent faults occur, the red light is always on.
PUL+Positive End of Control Pulse SignalConnect to signal power,+5V to +24V can be driven.
PUL-Negative End of Control Pulse SignalThe falling edge is valid, and the motor takes one step whenever the pulse changes from high to low. Input resistance 220Ω. Requirements: low level 0 to 0.5V, high level 4 to 5V, Pulse charge >2.5us.
DIR+Positive End of Directional SignalConnect to signal power,+5V to +24V can be driven.
DIR-Negative End of Directional SignalUsed to change the direction of the motor. Input resistance 220Ω. Requirements: low level 0 to 0.5V, high level 4 to 5V, Pulse charge >2.5us.
ENA+Positive End of Enabling SignalConnect to signal power,+5V to +24V can be driven.
ENA-Negative End of Enabling SignalWhen it is valid (low level), the motor coil current is turned off, the driver stops working, and the motor is in a free state.
ALM+Positive End of Alarm Signal OutputWhen over-current, over-voltage, under-voltage or over-tolerance alarms, the alarm signal is valid (the output photocoupler is turned on). ALM+ is connected to the pull-up power to use the positive pole of the output power supply, and ALM- is connected to the negative pole of the output power supply. Maximum drive current 50mA.
ALM-Negative End of Alarm Signal Output
EZ+/EZ-Positive/Negative End of Encoder Z Phase InputPositive input/negative input of Connecting to encoder Z channel
EB+/EB-Positive/Negative End of Encoder B Phase InputPositive input/negative input of Connecting to encoder B channel
EA+/EA-Positive/Negative End of Encoder A Phase InputPositive input/negative input of Connecting to encoder A channel
VCCEncoder Power Supply5V encoder power supply
GNDGround of Encoder Power SupplyGround of Encoder Power Supply
A+A-Motor WiringFour lead wires
B+B-

Microstep Segmentation Setting

Pulse/RevoSW1SW2SW3SW4
Defaultonononon
800offononon
1600onoffonon
3200offoffonon
6400ononoffon
12800offonoffon
25600onoffoffon
500offoffoffon
1000onononoff
2000offononoff
4000onoffonoff
5000offoffonoff
8000ononoffoff
10000offonoffoff
3600onoffoffoff
7200offoffoffoff

Dimensions (Unit: mm)

Dimensions of 1A to 6A Digital Closed Loop Stepper Motor Driver

Wiring Diagram

Wiring Diagram of 1A to 6A Digital Closed Loop Stepper Motor Driver

Details

1A~6A Closed Loop Stepper Motor Driver Details

Tips: How to set up a 2 phase stepper motor driver

Usually the step angle of a two-phase stepper motor is 1.8 degrees. It is calculated that it takes 200 pulses to make one revolution, that is, it needs to walk 200 steps, and each step is 1.8 degrees. Generally, two phase hybrid stepper motor drivers are equipped with switches to adjust the number of subdivisions. You can easily set the desired number of subdivisions by flipping the corresponding setting switch against the setting table.

Two phase bipolar stepper motor driver setting table has two forms, one is the subdivision number, and the other is to directly give the number of pulses required for each revolution under different subdivision numbers. In order to adapt to stepping motors with different rated currents, the drive generally has an adjustment function, and the adjustment method is also different. Generally, two forms of potentiometer or dial switch are used. The most commonly used is the dial switch form. Appropriate current parameters should be selected when setting, the greater the current, the greater the torque that the motor can generate.

In order to reduce the heating of the motor, many drivers have a half-current function. When the half-current switch is turned on, the stepper motor driver will reduce the current to the set value if it does not receive a pulse signal within a short period of time. Half, let the motor better heat dissipation. But when this function is used, the locking torque will be reduced correspondingly in the half-flow state, so it needs to be selected according to actual needs.

Product reviews
I really recommend everyone to buy
5
Dpolister
Avatar
12/8/2021 6:25 PM
This 2 phase closed loop stepper motor driver is super affordable, good quality and low price. I just bought it and used it. Generally speaking, I am very satisfied with it. I sincerely recommend everyone to buy, don't worry about quality problems.
Was this review helpful? Yes No (0/0)
Overall performance is good and meets my expectations
4
Gavin
Avatar
12/8/2025 12:59 AM
Stable performance, low noise, and fast response. The auto current adjustment is hassle-free, and the full protection features make the motor run smoothly and reliably.
Was this review helpful? Yes No (0/0)
Only registered users can write reviews
Customers who bought this item also bought

Digital Stepper Motor Driver, 2 Phase, DC 24V ~ 50V

ATO-STEP-M504T
$91.39
Low price digital stepper driver powered by DC 18V ~ 36V/ AC 20V ~ 40V power supply, adjustable drive current from 1A to 4.5A, capable of driving Nema 23 hybrid 2 phase stepper motors. This stepper motor controller can realize precise position control even without a feedback system.

Digital Stepper Motor Driver, 2 Phase, DC 24V ~ 80V

ATO-STEP-M808T
$121.69
Digital stepper driver powered by DC 24V ~ 80V/ AC 20V ~ 70V can drive Nema 34 2 phase hybrid stepper motor for CNC machine, 3D printer and robot arm, adjustable drive current from 2.4A to 7.8A, pulse frequency up to 250Kpps.

Closed Loop Stepper Motor Driver, 2 Phase, 2A ~ 8A

ATO-STEP-B808T
$115.39
2 phase stepper driver for sale, DC 24V ~ 80V/ AC 20V ~ 70V power supply, drive current 2A ~ 8A, impulse response frequency up to 250Kpps. The hybrid stepper motor driver is high performance for driving Nema 34 closed loop bipolar stepper motor.

Nema 34 Stepper Motor, 2 Phase, 4A, 8.5N·m

ATO-STEP-34L400
$183.13
Nema 34 (86 x 86mm) hybrid bipolar stepper motor for sale, comes with holding torque of 850N·cm (8.5N·m), 14mm or 12.7mm shaft, 1.8 degree step angle, 4 wire connections, suitable for CNC machine, 3D printer and robot arm, etc. This hybrid stepper motor draws high current of up to 4 amps with a step accuracy of ±5%.

Nema 34 Closed Loop Stepper Motor, 2 Phase, 6.2A, 12N·m

ATO-STEP-34CC620
$281.09
Nema 34 closed loop stepper motor with encoder, 86 x 86 x 172mm, is a high torque stepper motor for CNC machine, 3D printer and robot arm. 6.2 amps 2 phase hybrid stepper motor comes with holding torque up to 12 N·m (1700 Oz.in), 12mm long shaft, 1.8 degree step angle, 4 wire connections.