Brushless DC Motor Controller for Electric Vehicle

$395.52
High speed BLDC motor controller is designed for electric motorcycles and electric scooters, equiped with powerful and intelligent microprocessor, up to 40000 electric RPM, compatible with 60 degrees or 120 degrees Hall position sensor and support any poles of brushless motor.
SKU: ATO-BLDC-KBL
*
*
*
Free Shipping
Delivery date: 8-12 days

BLDC MOTOR CONTROLLER FEATURES

  • Specially designed for electric vehicles like electric motorcycles and scooters.
  • Powerful and intelligent microprocessor.
  • High-speed low-loss synchronous rectification PWM modulation.
  • Strict current limit and torque control.
  • Greater starting current can get a faster start-up speed.
  • It has a battery protection function: When the battery voltage is low, the alarm will be timely and the current attenuation, low output to stop the protection of the battery.
  • With over-temperature protection: When the temperature is too high or too low will automatically current attenuation to protect the controller and battery.

BLDC MOTOR CONTROLLER SPECIFICATION

Basic Parameters
ModelATO-KBL/ATO-KEB
Matching ATO BLDC Motor ModelATO-BLDC-600R1 (600W BLDC Motor)
ATO-BLDC-750R3 (750W BLDC Motor)
ATO-BLDC-1000R1 (1 kW BLDC Motor)
ATO-BLDC-2300R3 (2.3 kW BLDC Motor)
ATO-BLDC-3000R3 (3 kW BLDC Motor)
ATO-BLDC-3800R3 (3.8 kW BLDC Motor)
ATO-BLDC-5000R3 (5 kW BLDC Motor)
ATO-BLDC-10KR2 (10 kW BLDC Motor)
Size200*146*62 mm
WeightFor 400W to 750W motor: 2kg
For 1kW to 3kW motor: 2.5-4kg
For 4kW to 6kW motor: 5-7kg
For 7kW to 9kW motor: 8-10kg
For 10kW to 12W motor: 11-13kg
For 13kW to 15kW motor: 14-17kg
Frequency of Operation16.6kHz
Standby Current< 0.5mA
5V Sensor Supply Current40mA
Controller supply voltage rangePWR, 18V to 120V
Supply CurrentPWR, 150mA
Controller Rated Current1.5-2 times the rated current of the motor
With CAN bus function (Optional)Yes, the controller supports CAN function, which provides communication based on CAN 2.0B extended frame and SAE J1939 protocol standard for vehicles. It can be used in vehicles, ships, AGVs and other equipment to exchange data with ECU and get speed and RPM feedback via CAN bus.
CAN bus communication rate: 250K
Download CAN Protocal
Analog Brake and Throttle Input0-5 Volts. Producing 0-5V signal with 3-wire pot.
Full Power Operating Temperature Range0℃ to 50℃
Operating Temperature Range-30℃ to 90℃
Protection GradeIP65
Peak Phase Current, 10 seconds50-120A (according to the model)
Continuous Phase Current Limit5-50A (according to the model)
Maximum Battery CurrentConfigurable
Basic Functions
  1. Fault detection and protection. It can identify faults via LED twinkling code.
  2. Battery voltage real-time monitoring. It will stop work when battery voltage is too high or too low.
  3. Built in current detection and over current protection.
  4. The controller is equipped with temperature measurement and protection functions. At low and high temperatures, the current is cut to protect the controller and the battery.
  5. Support 5V sensor power supply.
  6. 3 switch inputs. Connect to GND for valid signal. The default is the pedal safety switch input (to be configured via the customer software), the brake switch input and the reversing switch input.
  7. The Boost switch can be configured. The controller will output the maximum current, when the switch is turned on.
  8. The Economy switch can be configured. Limiting the maximum drive current to the controller is half the normal case, when the switch is turned on.
  9. 12V brake signal input can be configured.
  10. 3-phase Hall position sensor input, open collector output and the controller provides pull-up resistor.

BLDC MOTOR CONTROLLER DIMENSION (Unit=mm)

BLDC motor controller dimesion

Details

Brushless DC Motor Controller for Electric Vehicle Details

TIPS: Why Do BLDC Motors Need to be Used with Controllers?

Reason 1: Brushless dc motor is a permanent magnet brushless synchronous motor, its functional parameters, model, power supply voltage, output power, phase Angle, or self-identification function must be used with the brushless motor controller, in order to use normally.

Reason 2: Brushless DC motor has no brush and commutator, there must be an electronic commutator to maintain the direction of rotation. The electronic commutator is composed of six power MOSFET transistors, which are controlled by a brushless motor controller. At the same time, the controller can also control the starting and stopping of the motor, forward and backward, speed regulation, over-voltage, over-current and under-voltage protection. So it is necessary to have a brushless motor controller, even if the brushless DC motor is directly powered on, it is useless.

ATO High Torque BLDC Motor Drawings & Price List

Note: 

1. ATO highly recommends 48V motors because all models of 48V are in stock, the price is cheaper and the delivery time is shorter, only about 7 days.

2. 24V/ 72V/ 96V motors are generally not in stock, need to be produced by the factory, which will cost more to start the production line and the delivery time will be longer, about 25 days.

3. The prices in the table are just for your reference. If you want to get the latest quotation, please feel free to contact us.

ModelMotor PriceController PriceRated PowerRated SpeedRated TorqueRotor InertiaMotor Weight
(USD/Piece)(USD/Piece)(kW) (RPM)(Nm)(Kgcm2)(Kg)
80mm Series DC Brushless Motor
ATO-80WDM01330 24/48/72/96V24V: 458.24395.520.4130001.30.62.4
48V: 305.49
72/96V: 580.43
ATO-80WDM02420 24/48/72/96V24V: 564.53395.520.520002.40.83
48V: 376.35
72/96V: 715.06
ATO-80WDM02430 24/48/72/96V24V: 529.16395.520.7530002.40.83
48V: 352.77
72/96V: 670.26
ATO-80WDM03320 24/48/72/96V24V: 597.68395.520.6920003.31.13
48V: 398.45
72/96V: 757.36
ATO-80WDM03330 24/48/72/96V24V: 639.27395.521.0430003.31.13
48V: 426.18
72/96V: 809.74
110mm Series DC Brushless Motor
ATO-110WDM02020 24/48/72/96V24V: 687.38395.520.4200023.33.2
48V: 458.25
72/96V: 824.85
ATO-110WDM02030 24/48/72/96V24V: 745.11395.520.6300023.33.2
48V: 496.74
72/96V: 894.13
ATO-110WDM04010 24/48/72/96V24V: 779.86395.520.4100046.55.65
48V: 519.93
72/96V: 935.87
ATO-110WDM04020 24/48/72/96V24V: 788.57395.520.8200046.55.65
48V: 525.71
72/96V: 988.33
ATO-110WDM04030 24/48/72/96V24V: 798.63653.051.3300046.55.65
48V: 532.42
72/96V: 1001.95
ATO-110WDM06010 24/48/72/96V24V: 758.82395.520.610006106.6
48V: 505.88
72/96V: 956.69
ATO-110WDM06020 24/48/72/96V24V: 819.59653.051.320006106.6
48V: 546.39
72/96V: 1010.82
ATO-110WDM06030 24/48/72/96V24V: 995.94653.051.930006106.6
48V: 553.28
72/96V: 1051.23
130mm Series DC Brushless Motor
ATO-130WDM04010 24/48/72/96V24V: 876.95395.520.41000410.46.7
48V: 584.62
72/96V: 1099.08
ATO-130WDM04020 24/48/72/96V24V: 910.67395.520.82000410.46.7
48V: 607.13
72/96V: 1104.98
ATO-130WDM04030 24/48/72/96V24V: 959.18653.051.33000410.46.7
48V: 639.45
72/96V: 1151.01
ATO-130WDM06010 24/48/72/96V24V: 987.65395.520.61000612.47.7
48V: 658.43
72/96V: 1185.17
ATO-130WDM06020 24/48/72/96V24V: 1012.23653.051.32000612.47.7
48V: 674.82
72/96V: 1147.19
ATO-130WDM06030 24/48/72/96V24V: 1047.72653.051.93000612.47.7
48V: 698.48
72/96V: 1208.34
ATO-130WDM07710 24/48/72/96V24V: 1060.07395.520.810007.715.89.05
48V: 706.71
72/96V: 1257.94
ATO-130WDM07720 24/48/72/96V24V: 1093.21653.051.620007.715.89.05
48V: 738.65
72/96V: 1292.64
ATO-130WDM07730 48/72/96V48V: 751.52653.052.330007.715.89.05
72/96V: 1337.71
ATO-130WDM10010 24/48/72/96V24V: 1161.55653.05110001021.412
48V: 784.83
72/96V: 1396.89
ATO-130WDM10020 24/48/72/96V24V: 1224.36653.05220001021.412
48V: 816.24
72/96V: 1371.28
ATO-130WDM10030 48/72/96V48V: 879.12898.213.130001021.412
72/96V: 1450.55
ATO-130WDM15010 24/48/72/96V24V:1311.88653.051.610001532.412
48V: 936.47
72/96V: 1498.35
ATO-130WDM15020 48/72/96V48V: 1086.36898.213.120001532.412
72/96V: 1738.17
ATO-130WDM15030 48/72/96V48V: 1127.541119.074.730001532.412
72/96V: 1804.64
180mm Series DC Brushless Motor
ATO-180WDM12010 48/72/96V48V: 1246.31653.051.310001232.618.5
72/96V: 1994.09
ATO-180WDM12020 48/72/96V48V: 1323.69653.052.520001232.618.5
72/96V: 2117.91
ATO-180WDM12030 48/72/96V48V: 1398.84898.213.83000123818.5
72/96V: 2238.14
ATO-180WDM16010 48/72/96V48V: 1555.69653.051.71000165518.6
72/96V: 2411.32
ATO-180WDM16020 48/72/96V48V: 1625.36898.213.42000165518.6
72/96V: 2568.07
ATO-180WDM16030 48/72/96V48V: 1745.931119.0753000165518.6
72/96V: 2618.89
ATO-180WDM25010 48/72/96V48V: 2012.54653.052.61000255526
72/96V: 3179.81
ATO-180WDM25020 48/72/96V48V: 2274.191119.075.22000259326
72/96V: 3411.26
ATO-180WDM25030 48/72/96V48V: 2448.581531.997.93000259326
72/96V: 3672.87
ATO-180WDM36010 48/72/96V48V: 2644.28898.213.810003614830
72/96V: 3966.42
ATO-180WDM36020 48/72/96V48V: 2832.561119.077.520003614830
72/96V: 4248.84
ATO-180WDM36030 72/96V72/96V: 4334.691885.1511.330003614830
ATO-180WDM50010 48/72/96V48V: 3284.581119.075.210005016538
72/96V: 4556.41
ATO-180WDM50020 48/72/96V48V: 4344.121531.9910.820005016538
72/96V: 5994.72
ATO-180WDM50030 96V96V: 6204.652261.8415.730005016538

Wiring ATO High Torque BLDC Motor With Controller

In this video, we will show you how to connect a ATO 400W-15kW 24V/48V/72V/96V high torque brushless DC motor with the matching controller.

How to Make Your BLDC Motor Forward and Reverse Control

If you want your electric car to be more powerful, try using ATO high torque BLDC motor kit as the power unit. It is a good idea. Refer to the video step by step to operate, you can achieve the forward and reverse control of the brushless DC motor.

This video shows you how to connect a 50W 24V 3 phase BLDC motor to its driver and achieve speed control.

In this video we've guided you through how to do VFD control wiring with a self-lock push button switch to run the motor in forward direction. We've covered everything from wiring to programming and even a test run. So just watch it through and hope you'll find it informative and helpful.

Modbus RS-485 Serial Communication with Upgraded BLDC Motor Driver

This video will provide you with step-by-step instructions for RS485 serial communication with an upgraded ATO BLDC driver rated at 30A/50A/100A.

Product reviews
Good service and high quality products
5
Naviathan
Avatar
1/22/2019 6:59 PM
I bought a 750W BLDC motor and this controller a few days ago. At first, I didn't know how to wire it to the motor, after watching the video recommended by ATO engineers, I found it very easy to use. Thanks for the good service and high quality products.
Was this review helpful? Yes No (1/1)
The value of the output voltage
4
Zakariae
Avatar
7/1/2019 5:51 AM
Hello,
I would like to know the values ​​of the output voltage of the Controller :

A: Output U/1/A phase,
B: Output V/2/B phase,
C: Output W/3/C phase,

Thank you.
Was this review helpful? Yes No (0/0)
ATO Responded
Controller A/B/C phase output is AC voltage, voltage value changes with the change of motor speed, not fixed value.
Technical problem of ATOTH-G Series BLDC Motor Controller
5
Matthew Ramirez
Avatar
7/22/2019 1:58 AM
For the ATOTH-G Series BLDC Motor Controller, do we have to configure the controller using the RS232 connection before using it?
Was this review helpful? Yes No (0/0)
ATO Responded
No need to configure anything via RS232 connection.
Once you receive the controller, you can plug terminals and run as per video we sent you.
ATOTH-G Series BLDC Motor Controller connection
5
Arkaprava
Avatar
8/6/2019 5:47 AM
Do we need to provide any other voltage apart from 24vdc to ATOTH-G Series BLDC Motor Controller B
Was this review helpful? Yes No (0/0)
ATOTH-G Series BLDC Motor Controller connection
5
Arkaprava
Avatar
8/6/2019 5:50 AM
For ATOTH-G Series BLDC Motor Controller, do we need to give any other input power supply apart from controller B
Was this review helpful? Yes No (0/0)
ATO Responded
No, you don't need any other power supply.
ATOTH-G Series BLDC Motor Controller connection
5
Arkaprava
Avatar
10/30/2019 4:04 AM
For ATOTH-G Series BLDC Motor Controller, is it mandatory to add contactor and pre charge resistor in Battery Positive input side?
In given video , no contactors and pre charge resistors are connected but in motor controller it is added to control inrush current.
Can you please tell me whether that contactor and precharge resistor are included in controller design?
Was this review helpful? Yes No (0/0)
ATO Responded
No need to add contactor and pre charge resistor in battery positive input side, just connect to the power supply directly.
Some things to make sure before buying
5
Paul Vitasek
Avatar
4/27/2020 7:10 PM
For your ATOTH-G Series BLDC Motor Controller, the user manual refers to a configuration mode through a serial connecion. But what can be configured into the controller ? parameters of the PI corrector ?
Was this review helpful? Yes No (1/0)
ATO Responded
1. You can view the general parameters of the motor connected by the controller through software, can set the peak current, brake parameters, etc. This software has few practical applications.
2. The controller has only RS232 interface.
Is the 0-5V speed circuit isolated for your BLDC motor controller?
5
Joel Forker
Avatar
5/10/2020 7:55 PM
Is the 0-5V speed circuit isolated for your BLDC motor controller? In other words, my control circuit requires that my 0-5V speed reference be sourced not from the  5V controller but from my own battery source. I will connect the 0V of my battery source to the COM on the controller. My reference voltage will connect to the reference input on the controller. I will NOT use the  5V source voltage on the controller.
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, you can use the battery voltage to provide 0-5V without using the controller's +5V, connect the 0V of the battery power to the COM on the controller, and connect the positive terminal of the battery to the SV of the controller.
I have some doubts about BLDC motor
5
Agnus
Avatar
10/27/2021 9:21 PM
For your ATOTH-G BLDC motor controller specification on the web site, it states a frequency of 16.6 kHz. One of our electrical engineers wanted to know how much of this will be reflected back to the DC bus?
Was this review helpful? Yes No (0/0)
ATO Responded
The frequency will drop when it is fed back to the DC bus, but it is mainly in the form of current, and has no effect on the voltage. Moreover, and if you need to increase the quality of the DC bus, you can simply add a DC low-pass filter on the feed side of the drive.
can the controller short time the peak power of 9.4kw ?
5
Jan
Avatar
1/6/2022 9:51 AM
Can I use the controller 2.6kw to 4kw for the ATO-BLDC-3800R3?
Can the controller also use the rated power of 3.8kw for the motor permanently.
And can the controller also short time the peak power of 9.4kw ?
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, you can choose a 2.6 to 4KW controller, and you can permanently use the motor's 3.8KW power. 9.4KW is the peak power of the motor, which does not affect the use of the controller.
Brushless DC motor controller error
5
Alston
Avatar
5/24/2022 9:45 PM
I recently purchased three "Brushless DC Motor Controller for Electric Vehicle" from you. Two of them work with no problems, but the third is giving us errors when trying to operate. It is giving us a 4,2 error code which is stated as a hall sensor error. Please let me know the best way to fix this error or the best course of action for me.
Was this review helpful? Yes No (0/0)
ATO Responded
You can test the third faulty motor with the first, or the second normal controller, and check if it still shows 4,2 error code? If it still fails, please check whether the Hall signal wiring of this motor is correct?
I am not getting any response from the motor
5
Logan
Avatar
5/26/2022 9:13 PM
I am trying to use the ATO-BLDC-TH-G motor controller using CAN commands. I am not getting any response from the motor even though I am sending commands to it. Do I need to wire anything other than the CAN pins for the motor controller to function? I am sending the following command: 1801E5D0 ,F4 01 96 01 00 00 00 00.
Was this review helpful? Yes No (0/0)
ATO Responded
Hi, Logan,

To better solve your problem,

1. Please let us know if there is any feedback when using CAN? Try changing 96 to 00.
2. Please take a picture of the model information on the back cover of the driver and provide us with a photo for verification.
3. It would be better if you could take .
Is it possible to change the CAN command ID through this RS232 configuration?
5
Biaxy
Avatar
6/1/2022 7:30 PM
We would like to use 4 of these motor controllers in a remote controlled vehicle. I noticed that all the controllers have the same command ID and our system will have a single CAN line to control all the motors. Our main controller only has 1 CAN bus. Is it possible to change the CAN command ID through this RS232 configuration? If so, could you send me the required software to modify the command ID number?
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, you can change the CAN command ID through software configuration, as shown in the attached picture. And only this software is available recently, you can try it out. Please check the software download link below.
Can you send a motor controller download again?
5
ronnie
Avatar
4/5/2023 7:24 PM
Good afternoon. We recently received a ATO-BLDC-TH-G and need the software for setting it up for our motors over RS-232. We used this software in the past but I no longer have it.
The main reason we need the software is this controller will be moved between 2 different motors for testing purposes and they are not the same size (a 2.5kW ATO-BLDC-2500R2 and a 3.8kW).
Is this a download you could send again?
Was this review helpful? Yes No (0/0)
ATO Responded
Please check the software in the attachment, and note that the motor should be stopped when using the software.
The controller you purchased is a 3kW version. If you are using it to drive a 3.8kW motor, the capacity may be too small, but you can test it first.
Hall Effect sensor
4
Coutard
Avatar
9/16/2025 9:14 PM
Hello, can the "Electric Vehicle Brushless DC Motor Controller" operate without Hall Effect sensors? Is there anything I need to switch to eliminate the Hall Effect sensors?
Was this review helpful? Yes No (0/0)
ATO Responded
Sorry, this controller (SKU: ATO-BLDC-KBL) requires Hall Effect sensors to operate; otherwise, a Hall Effect sensor fault will be reported.
Frequency control accuracy
5
Cuguti
Avatar
10/14/2026 1:04 AM
Could you please confirm whether the frequency control accuracy of the ATO-BLDC-KBL is better than (or lower than) 0.2%?
Was this review helpful? Yes No (0/0)
ATO Responded
The frequency control accuracy of the BLDC-KBL cannot be better than (i.e., the deviation is less than) 0.2%; its control accuracy is around 5%.
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

BLDC MOTOR CONTROLLER FEATURES

  • Specially designed for electric vehicles like electric motorcycles and scooters.
  • Powerful and intelligent microprocessor.
  • High-speed low-loss synchronous rectification PWM modulation.
  • Strict current limit and torque control.
  • Greater starting current can get a faster start-up speed.
  • It has a battery protection function: When the battery voltage is low, the alarm will be timely and the current attenuation, low output to stop the protection of the battery.
  • With over-temperature protection: When the temperature is too high or too low will automatically current attenuation to protect the controller and battery.

BLDC MOTOR CONTROLLER SPECIFICATION

Basic Parameters
ModelATO-KBL/ATO-KEB
Matching ATO BLDC Motor ModelATO-BLDC-600R1 (600W BLDC Motor)
ATO-BLDC-750R3 (750W BLDC Motor)
ATO-BLDC-1000R1 (1 kW BLDC Motor)
ATO-BLDC-2300R3 (2.3 kW BLDC Motor)
ATO-BLDC-3000R3 (3 kW BLDC Motor)
ATO-BLDC-3800R3 (3.8 kW BLDC Motor)
ATO-BLDC-5000R3 (5 kW BLDC Motor)
ATO-BLDC-10KR2 (10 kW BLDC Motor)
Size200*146*62 mm
WeightFor 400W to 750W motor: 2kg
For 1kW to 3kW motor: 2.5-4kg
For 4kW to 6kW motor: 5-7kg
For 7kW to 9kW motor: 8-10kg
For 10kW to 12W motor: 11-13kg
For 13kW to 15kW motor: 14-17kg
Frequency of Operation16.6kHz
Standby Current< 0.5mA
5V Sensor Supply Current40mA
Controller supply voltage rangePWR, 18V to 120V
Supply CurrentPWR, 150mA
Controller Rated Current1.5-2 times the rated current of the motor
With CAN bus function (Optional)Yes, the controller supports CAN function, which provides communication based on CAN 2.0B extended frame and SAE J1939 protocol standard for vehicles. It can be used in vehicles, ships, AGVs and other equipment to exchange data with ECU and get speed and RPM feedback via CAN bus.
CAN bus communication rate: 250K
Download CAN Protocal
Analog Brake and Throttle Input0-5 Volts. Producing 0-5V signal with 3-wire pot.
Full Power Operating Temperature Range0℃ to 50℃
Operating Temperature Range-30℃ to 90℃
Protection GradeIP65
Peak Phase Current, 10 seconds50-120A (according to the model)
Continuous Phase Current Limit5-50A (according to the model)
Maximum Battery CurrentConfigurable
Basic Functions
  1. Fault detection and protection. It can identify faults via LED twinkling code.
  2. Battery voltage real-time monitoring. It will stop work when battery voltage is too high or too low.
  3. Built in current detection and over current protection.
  4. The controller is equipped with temperature measurement and protection functions. At low and high temperatures, the current is cut to protect the controller and the battery.
  5. Support 5V sensor power supply.
  6. 3 switch inputs. Connect to GND for valid signal. The default is the pedal safety switch input (to be configured via the customer software), the brake switch input and the reversing switch input.
  7. The Boost switch can be configured. The controller will output the maximum current, when the switch is turned on.
  8. The Economy switch can be configured. Limiting the maximum drive current to the controller is half the normal case, when the switch is turned on.
  9. 12V brake signal input can be configured.
  10. 3-phase Hall position sensor input, open collector output and the controller provides pull-up resistor.

BLDC MOTOR CONTROLLER DIMENSION (Unit=mm)

BLDC motor controller dimesion

Details

Brushless DC Motor Controller for Electric Vehicle Details

TIPS: Why Do BLDC Motors Need to be Used with Controllers?

Reason 1: Brushless dc motor is a permanent magnet brushless synchronous motor, its functional parameters, model, power supply voltage, output power, phase Angle, or self-identification function must be used with the brushless motor controller, in order to use normally.

Reason 2: Brushless DC motor has no brush and commutator, there must be an electronic commutator to maintain the direction of rotation. The electronic commutator is composed of six power MOSFET transistors, which are controlled by a brushless motor controller. At the same time, the controller can also control the starting and stopping of the motor, forward and backward, speed regulation, over-voltage, over-current and under-voltage protection. So it is necessary to have a brushless motor controller, even if the brushless DC motor is directly powered on, it is useless.

Product reviews
Good service and high quality products
5
Naviathan
Avatar
1/22/2019 6:59 PM
I bought a 750W BLDC motor and this controller a few days ago. At first, I didn't know how to wire it to the motor, after watching the video recommended by ATO engineers, I found it very easy to use. Thanks for the good service and high quality products.
Was this review helpful? Yes No (1/1)
The value of the output voltage
4
Zakariae
Avatar
7/1/2019 5:51 AM
Hello,
I would like to know the values ​​of the output voltage of the Controller :

A: Output U/1/A phase,
B: Output V/2/B phase,
C: Output W/3/C phase,

Thank you.
Was this review helpful? Yes No (0/0)
ATO Responded
Controller A/B/C phase output is AC voltage, voltage value changes with the change of motor speed, not fixed value.
Technical problem of ATOTH-G Series BLDC Motor Controller
5
Matthew Ramirez
Avatar
7/22/2019 1:58 AM
For the ATOTH-G Series BLDC Motor Controller, do we have to configure the controller using the RS232 connection before using it?
Was this review helpful? Yes No (0/0)
ATO Responded
No need to configure anything via RS232 connection.
Once you receive the controller, you can plug terminals and run as per video we sent you.
ATOTH-G Series BLDC Motor Controller connection
5
Arkaprava
Avatar
8/6/2019 5:47 AM
Do we need to provide any other voltage apart from 24vdc to ATOTH-G Series BLDC Motor Controller B
Was this review helpful? Yes No (0/0)
ATOTH-G Series BLDC Motor Controller connection
5
Arkaprava
Avatar
8/6/2019 5:50 AM
For ATOTH-G Series BLDC Motor Controller, do we need to give any other input power supply apart from controller B
Was this review helpful? Yes No (0/0)
ATO Responded
No, you don't need any other power supply.
ATOTH-G Series BLDC Motor Controller connection
5
Arkaprava
Avatar
10/30/2019 4:04 AM
For ATOTH-G Series BLDC Motor Controller, is it mandatory to add contactor and pre charge resistor in Battery Positive input side?
In given video , no contactors and pre charge resistors are connected but in motor controller it is added to control inrush current.
Can you please tell me whether that contactor and precharge resistor are included in controller design?
Was this review helpful? Yes No (0/0)
ATO Responded
No need to add contactor and pre charge resistor in battery positive input side, just connect to the power supply directly.
Some things to make sure before buying
5
Paul Vitasek
Avatar
4/27/2020 7:10 PM
For your ATOTH-G Series BLDC Motor Controller, the user manual refers to a configuration mode through a serial connecion. But what can be configured into the controller ? parameters of the PI corrector ?
Was this review helpful? Yes No (1/0)
ATO Responded
1. You can view the general parameters of the motor connected by the controller through software, can set the peak current, brake parameters, etc. This software has few practical applications.
2. The controller has only RS232 interface.
Is the 0-5V speed circuit isolated for your BLDC motor controller?
5
Joel Forker
Avatar
5/10/2020 7:55 PM
Is the 0-5V speed circuit isolated for your BLDC motor controller? In other words, my control circuit requires that my 0-5V speed reference be sourced not from the  5V controller but from my own battery source. I will connect the 0V of my battery source to the COM on the controller. My reference voltage will connect to the reference input on the controller. I will NOT use the  5V source voltage on the controller.
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, you can use the battery voltage to provide 0-5V without using the controller's +5V, connect the 0V of the battery power to the COM on the controller, and connect the positive terminal of the battery to the SV of the controller.
I have some doubts about BLDC motor
5
Agnus
Avatar
10/27/2021 9:21 PM
For your ATOTH-G BLDC motor controller specification on the web site, it states a frequency of 16.6 kHz. One of our electrical engineers wanted to know how much of this will be reflected back to the DC bus?
Was this review helpful? Yes No (0/0)
ATO Responded
The frequency will drop when it is fed back to the DC bus, but it is mainly in the form of current, and has no effect on the voltage. Moreover, and if you need to increase the quality of the DC bus, you can simply add a DC low-pass filter on the feed side of the drive.
can the controller short time the peak power of 9.4kw ?
5
Jan
Avatar
1/6/2022 9:51 AM
Can I use the controller 2.6kw to 4kw for the ATO-BLDC-3800R3?
Can the controller also use the rated power of 3.8kw for the motor permanently.
And can the controller also short time the peak power of 9.4kw ?
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, you can choose a 2.6 to 4KW controller, and you can permanently use the motor's 3.8KW power. 9.4KW is the peak power of the motor, which does not affect the use of the controller.
Brushless DC motor controller error
5
Alston
Avatar
5/24/2022 9:45 PM
I recently purchased three "Brushless DC Motor Controller for Electric Vehicle" from you. Two of them work with no problems, but the third is giving us errors when trying to operate. It is giving us a 4,2 error code which is stated as a hall sensor error. Please let me know the best way to fix this error or the best course of action for me.
Was this review helpful? Yes No (0/0)
ATO Responded
You can test the third faulty motor with the first, or the second normal controller, and check if it still shows 4,2 error code? If it still fails, please check whether the Hall signal wiring of this motor is correct?
I am not getting any response from the motor
5
Logan
Avatar
5/26/2022 9:13 PM
I am trying to use the ATO-BLDC-TH-G motor controller using CAN commands. I am not getting any response from the motor even though I am sending commands to it. Do I need to wire anything other than the CAN pins for the motor controller to function? I am sending the following command: 1801E5D0 ,F4 01 96 01 00 00 00 00.
Was this review helpful? Yes No (0/0)
ATO Responded
Hi, Logan,

To better solve your problem,

1. Please let us know if there is any feedback when using CAN? Try changing 96 to 00.
2. Please take a picture of the model information on the back cover of the driver and provide us with a photo for verification.
3. It would be better if you could take .
Is it possible to change the CAN command ID through this RS232 configuration?
5
Biaxy
Avatar
6/1/2022 7:30 PM
We would like to use 4 of these motor controllers in a remote controlled vehicle. I noticed that all the controllers have the same command ID and our system will have a single CAN line to control all the motors. Our main controller only has 1 CAN bus. Is it possible to change the CAN command ID through this RS232 configuration? If so, could you send me the required software to modify the command ID number?
Was this review helpful? Yes No (0/0)
ATO Responded
Yes, you can change the CAN command ID through software configuration, as shown in the attached picture. And only this software is available recently, you can try it out. Please check the software download link below.
Can you send a motor controller download again?
5
ronnie
Avatar
4/5/2023 7:24 PM
Good afternoon. We recently received a ATO-BLDC-TH-G and need the software for setting it up for our motors over RS-232. We used this software in the past but I no longer have it.
The main reason we need the software is this controller will be moved between 2 different motors for testing purposes and they are not the same size (a 2.5kW ATO-BLDC-2500R2 and a 3.8kW).
Is this a download you could send again?
Was this review helpful? Yes No (0/0)
ATO Responded
Please check the software in the attachment, and note that the motor should be stopped when using the software.
The controller you purchased is a 3kW version. If you are using it to drive a 3.8kW motor, the capacity may be too small, but you can test it first.
Hall Effect sensor
4
Coutard
Avatar
9/16/2025 9:14 PM
Hello, can the "Electric Vehicle Brushless DC Motor Controller" operate without Hall Effect sensors? Is there anything I need to switch to eliminate the Hall Effect sensors?
Was this review helpful? Yes No (0/0)
ATO Responded
Sorry, this controller (SKU: ATO-BLDC-KBL) requires Hall Effect sensors to operate; otherwise, a Hall Effect sensor fault will be reported.
Frequency control accuracy
5
Cuguti
Avatar
10/14/2026 1:04 AM
Could you please confirm whether the frequency control accuracy of the ATO-BLDC-KBL is better than (or lower than) 0.2%?
Was this review helpful? Yes No (0/0)
ATO Responded
The frequency control accuracy of the BLDC-KBL cannot be better than (i.e., the deviation is less than) 0.2%; its control accuracy is around 5%.
Only registered users can write reviews
Customers who bought this item also bought

3 hp (2.3 kW) Brushless DC Motor, 48V/72V/96V, 7.3 Nm

ATO-BLDC-2300R3
$751.52
3 hp (2.3 kW) brushless DC electric motor kit (3 phase BLDC motor + BLDC controller + planetary gearbox ) at best price. Features 3000 rpm rated speed and 7.3 Nm holding torque, peak torque up to 23 Nm, operating at DC 48 volt, 72 volt, 96 volt.

4 hp (3 kW) Brushless DC Motor, 48V/72V/96V, 10 Nm

ATO-BLDC-3000R3
$879.12
4 hp (3 kW) 3-phase brushless DC electric motor comes with 130mm flange size, 3000 rpm rated speed, 10 Nm holding torque and peak torque up to 20 Nm. 48V/ 72V/ 96V high torque BLDC motor combines with controller best for electric car.

Circular Connector, 2/3/4/10/11/12/14 Pin, M19

ATO-CIRCN-19M
$49.52
Circular connector has simple and firm locking mechanism, easy to seal, insert and dismantle. Circular connector has 2/3/4/5/6/7/8/9/10/11/12/14 pin, different shapes of plug & socket to select.

2 hp (1.5 kW) Brushless DC Motor, 36V/48V, 4.78 Nm

ATO-BLDC-1500R3
$432.36
Buy best 1500 watt brushless DC motor kit (3 phase BLDC motor and controller) at low price for your electric car. Motor features 3000 rpm rated speed, 4.78 Nm holding torque, peak torque up to 14.33 Nm, working at 36V / 48V DC power supply.

5kW Brushless DC Motor, 48V/72V/96V, 16 Nm

ATO-BLDC-5000R3
$1,746.93
Buy 3 phase 5kW brushless DC motor and BLDC controller for your electric car at lower cost. 48V BLDC electric motor features 16 Nm high holding torque, peak torque up to 42 Nm, 3000 rpm rated speed, 72V/ 96V voltage is optional.