Rotary torque sensors have capacity range from 0.05 Nm, 0.2 Nm, 5 Nm, 20 Nm, 100 Nm, 200 Nm, 300 Nm, 500 Nm, 1000 Nm, 2000 Nm, 5000 Nm, 10000 Nm, 20000 Nm, 50000 Nm to 300000 Nm. Torque sensor capacity can be customized according to customer requirements.
After purchasing one ATO rotary torque sensor, you can buy a special torque meter ATO-DPM-DYN303 to obtain readings directly, or buy a F/I or F/V transmitter in drop-down list to transmit frequency signal to 4-20mA/1-5V signal.
Specification
| Model | ATO-DYN-210 |
| Shipping Weight | 5~1000kg |
| Capacity Range * | 10 Nm ~ 0-300000 Nm (For 150000-300000 Nm capacity, please contact us for a quote.) |
| Accuracy * | ±0.1%FS (for capacity<1000 Nm), ±0.2%FS (for capacity>1000 Nm), ±0.5%F.S (for all capacity) |
| Power Supply * | ±15V DC (≥50mA), 24V DC |
| Output Signal * | 5-15kHz, 4-20mA (add external F/I transmitter), 1-5V (add external F/V transmitter), download transmitter user manual |
| Max. Speed | ≤15000rpm |
| Maximum Torsion angle | 2.60x10rad(0.149°) |
| Speed Range | 0-3000rpm, 0-6000rpm, 0-8000rpm, maximum speed 10000rpm |
| Speed Signal | 120/60/10 pulse/turn (measuring range>10000 Nm, it will reach 180 pulse/turn) |
| Temperature Drift on Zero | 0.01%F.S/10℃ |
| Operating Temperature | -10℃~+50℃ |
| Humidity | 0~85%RH |
| Torsion Constant | 3.85x10Nm/rad |
| Response Time | 1kHz |
| Insulation Resistance | 1000MΩ |
| Inertia Moment | 0.38 Kgcm |
| Stability | 0.3%FS/year |
| Zero Output | ±2%F.S. |
| Safety Overload | 150%F.S |
| Breaking Load | 200%F.S |
| Bridge Voltage | DC 10V |
| Material | Alloy steel |
| Protection Class | IP65 |
| Electrical Connection | circular connector |
| Wiring | Red: +24V; Black: GND; Green: Torque signal; White: RPM signal; Yellow: Shielded wire (can be disconnected) |
| Cable Length | 3m (Φ5mm), or other customizable lengths |
| Ultimate Cable tension | 98N |
Rotary Torque Sensor Dimension (unit: mm)

| Capacity | Dimension (mm) | |||||||||||||||
| Φdj6 | ΦD | A | L | L1 | H | h | E | E1 | B | B1 | C | F | S | Speed (rpm) | C Key size (b*l1*m) | |
| 10, 20, 30, 40, 50, 100 Nm | 18 | 85 | 150 | 224 | 32 | 123 | 58 | 72 | 95 | 62 | 90 | 6.5 | 112 | 10 | 6000 | 6*32*6*1 |
| 200, 300 Nm | 28 | 95 | 152 | 242 | 42 | 133 | 63 | 72 | 95 | 62 | 90 | 6.5 | 121 | 10 | 5000 | 8*42*7*1 |
| 500, 700 Nm | 38 | 105 | 154 | 272 | 56 | 144 | 69 | 72 | 95 | 62 | 90 | 6.5 | 136 | 10 | 4000 | 10*56*8*2 |
| 1000 Nm | 48 | 115 | 156 | 328 | 82 | 150 | 70 | 72 | 95 | 82 | 110 | 8.5 | 165 | 12 | 3000 | 14*82*9*2 |
| 2000, 3000 Nm | 65 | 132 | 165 | 385 | 105 | 172 | 80 | 72 | 95 | 82 | 110 | 8.5 | 192.5 | 12 | 2500 | 18*105*11*2 |
| 5000, 7000 Nm | 75 | 146 | 180 | 396 | 105 | 187 | 89 | 72 | 95 | 82 | 110 | 8.5 | 210 | 12 | 2000 | 20*105*12*2 |
| 10000, 20000 Nm | 100 | 182 | 180 | 447 | 130 | 244 | 122 | 80 | 110 | 112 | 140 | 10.5 | 230 | 15 | 2000 | 28*130*16*2 |
| 50000 Nm | 165 | 250 | 185 | 700 | 240 | 331 | 180 | 120 | 190 | 150 | 190 | 12.5 | 350 | 15 | 1900 | 40*240*22*2 |
| 100000 Nm | 210 | 330 | 200 | 820 | 300 | 410 | 210 | 160 | 200 | 250 | 290 | 12.5 | 410 | 15 | 1700 | 50*300*28*2 |
| 150000 Nm | 235 | 350 | 250 | 900 | 315 | 420 | 220 | 220 | 260 | 250 | 290 | 17 | 450 | 15 | 1200 | 56*315*32*2 |
| 200000 Nm | 255 | 360 | 210 | 900 | 320 | 446 | 140 | 220 | 260 | 250 | 290 | 17 | 450 | 15 | 1100 | 56*320*32*2 |
Rotary Torque Sensor Installation

Details

Diagram of Forces

Tips: How to install a rotary torque sensor?
The steps of torque sensor installation:
- According to the connection form of the shaft and the length of the rotary torque sensor, determine the distance between the prime mover and the load. Adjust the distance between the axes of the prime motor and the load relative to the base level, enable the axes concentricity to be less than Φ0.03 mm. Fix the original motor and load on the base level.
- Install the couplings on the shafts respectively.
- Adjust the distance between the torque sensor and the base level, enable the concentricity of their axis (torque sensor, motor and load) to be less than Φ0.03 mm, and fix the torque sensor on the base level.
- Tighten the coupling and complete the installation.
The requirements of torque sensor installation:
- Power equipment, torque sensor, and load equipment should be installed on a stable foundation to avoid excessive vibration, otherwise, data instability, measurement accuracy reduction, and even damage to the dynamic torque sensor will probably occur.
- Choose the elastic pin coupling or rigid coupling for connection. When the vibration is serious or the concentricity is greater than 0.05mm, it is recommended to use a flexible coupling and install a bearing support at the left and right ends of the torque sensor.
- Adjust the centre height and concentricity of the power equipment, load, and torque sensor separately, which is required to be lower than 0.05mm, and then fix.
Matters needing attention:
- The torque sensor should be installed in an environment where the ambient temperature is 0 ℃ ~ 60 ℃, the relative humidity is less than 90%, and there is no flammable or explosive product.
- It is not suggested to be installed in an environment with strong electromagnetic interference.
Product reviews
Views on rotary torque sensor
Avid
6/17/2021 2:17 AM
I am using your rotary torque sensor, I connected the sensor with the information you kindly send me, I am reading mv, but my controller needs 0 to 5V. What is your thinking about it?
Was this review helpful? (0/0)
Questions about rotary torque sensor
Magw
11/14/2021 7:53 PM
I am using your rotary torque sensor. I connected the sensor with the information you kindly sent me. I am reading mV, but my controller needs 0 to 5V. What are you thinking about it?
Was this review helpful? (0/0)
Torque sensor parameters and performance issues
Drdoug
11/22/2021 12:22 AM
I want to buy 5 of your ATO torque sensors, output /-5V. When I checked its user manual, I found that there are pins 7 (RPM ) and 8 (RPM-) on the last page to read the machine speed in RPM.
1. What is the voltage level of these pins?
2. How to use my microcontroller to read these pins to calculate the machine speed?
1. What is the voltage level of these pins?
2. How to use my microcontroller to read these pins to calculate the machine speed?
Was this review helpful? (0/0)
Hello, I would like to consult your rotary torque sensor.
Tracy
12/13/2021 1:06 AM
Hello, I am planning to use your rotary torque sensor in line with a stepper motor to measure torque applied to electrical connectors. I have noticed that some similar test bench layouts utilize a brake or clutch in conjunction with the transducer. Can you explain to me why this might be necessary? The torque we are applying is small (Max 7-8 n*m). We are also using a stepper motor to reverse directions during the testing process. Do you think it would be necessary to use an eddy current brake or clutch with this rotary torque transducer to obtain accurate and consistent measurements or do you think the use of a stepper motor may eliminate the need for the use of a brake or clutch? Also, can you recommend shaft couplings for this type of application? I couldn't find much information on the use of clutches and brakes with torque sensors/transducers. Any help will be greatly appreciated. Thanks.
Was this review helpful? (0/0)
I want to know about your torque sensor.
Munge
12/17/2021 12:18 AM
Can your torque sensor be setup such that one end is connected to the motor while the other end is connected to nothing? What sort of reading will I get if this is the case?
Was this review helpful? (0/0)
Is rotary torque sensor minimum 0.03% or 0.3%?
Betty
4/6/2023 3:06 AM
Thanks. Did you mean to say minimum 0.03% or 0.3%?
I had the option to select 0.1% on the website.
I had the option to select 0.1% on the website.
Was this review helpful? (0/0)
Can you customize this torque sensor capacity range?
doro
4/6/2023 8:50 PM
Our requirement is up to 3400Nm. If we go with the 3000Nm unit, and exceed the torque on the shaft for short duration, will we damage the sensor?
Is it possible to customize the unit to have a capacity range of ~5 to 3500Nm with accuracy of ±0.02% of F.S.?
Is it possible to customize the unit to have a capacity range of ~5 to 3500Nm with accuracy of ±0.02% of F.S.?
Was this review helpful? (0/0)
Can rotary torque sensor handle any axial load?
amora
4/7/2023 12:23 AM
A few questions on the item below:
Can it handle any axial load? If so, how much and can it measure axial load in addition to torque and speed?
What is the data output frequency? It is indicated as 60 pulses/turn, so does it mean that it will give 6000 pulses per minute if operating at 100rpm, i.e. 100 pulses per second, or 100 Hz? And then at maximum 4800rpm, it will have a output frequency of 4800 Hz? Does it come with any warranty?
What is the lead time for shipping to Edmonton, Alberta, Canada?
Can it handle any axial load? If so, how much and can it measure axial load in addition to torque and speed?
What is the data output frequency? It is indicated as 60 pulses/turn, so does it mean that it will give 6000 pulses per minute if operating at 100rpm, i.e. 100 pulses per second, or 100 Hz? And then at maximum 4800rpm, it will have a output frequency of 4800 Hz? Does it come with any warranty?
What is the lead time for shipping to Edmonton, Alberta, Canada?
Was this review helpful? (0/0)
Wiring information for the torque sensor
lolly
7/24/2023 7:10 PM
We are looking for wiring information for the ATO-TQS-D01 sensor we just received from you. We contacted you through your website and were told to get in touch via this email address.
Was this review helpful? (0/0)
Can you recommend a suitable sensor device?
janaya
7/26/2023 3:56 AM
We are working on a project that requires the use of a rotary valve and we would like to make sure we can automatically monitor for torque increases as well potentially reverse the valve for 0.25 – 1 seconds at some torque threshold to free up any jammed material – before resuming normal operations.
Can you recommend a suitable device?
Would the ATO-TQS-D03 work?
Please quote me 1 unit if suitable.
The motor for the rotary valve: 1/2 HP Explosion Proof TE 230/460V/3PH/60HZ Motor
Can you recommend a suitable device?
Would the ATO-TQS-D03 work?
Please quote me 1 unit if suitable.
The motor for the rotary valve: 1/2 HP Explosion Proof TE 230/460V/3PH/60HZ Motor
Was this review helpful? (0/0)
can in connect to an arduino uno
Alexandros
12/20/2023 5:53 AM
I am new to engineering and i am looking to create an isometric dynamometer that measures the torque of the ankle which can peak up to 500nm do you think that torque sensor will be suitable. Also I am very new to engineering can this be connected to an arduino uno ?
Was this review helpful? (0/0)
INA terminal
Ives
9/19/2024 12:05 AM
The speed frequency input (INA terminal) is this where the torque frequency output from the torque sensor goes?
Was this review helpful? (0/0)
Purchase inquiry
Rossi
3/18/2026 12:58 AM
Could you please provide the model numbers for ATO-TQS-D01 and ATO-SERVO-DC2000? Also, do you have any recommended servo controllers?
Was this review helpful? (0/0)
Torque sensor range
Nautia
9/18/2026 2:20 AM
If I choose a model with a 10 Nm range and 0.2% resolution, I understand that the sensor can measure torque up to 10 Nm with a resolution of 0.02 Nm. Is that correct?
Was this review helpful? (0/0)
Only registered users can write reviews
Customers who bought this item also bought
Digital Torque Meter for Dynamic Torque/Speed/Power, 5 digit
ATO-DPM-RTS5D
$489.98
Digital torque meter with 3-channel 5 digit LED can real-time display dynamic torque, speed and power value. The measuring range of torque can be -99999~99999 Nm (display value is 0~99999 Nm). Digital panel meter for rotary torque sensor has power supply AC 220V, measuring speed 25 times/s, output analog signal 4-20mA, optional communication output RS485/RS232, optional external power supply DC 15V/24V.
Reaction Torque Sensor, Dual Flange, 20 Nm/100 Nm/5000 Nm to 10000 Nm
ATO-TQS-S01
$193.92
Torque sensor is a strain gauge sensor for static torque measurement. Static torque sensor has double-flange, a 5 pin male plug and no mounting base so it can be easy to install. Reaction torque sensors have a capacity range from 20 Nm/300 Nm/2000 Nm to 10000 Nm and can measure both forward and reverse torque.
Magnetic Particle Brake, Single Shaft, 3Nm-400Nm
ATO-PB
$319.89
Magnetic particle brake, single shaft, rated torque can select 6Nm, 12Nm, 25Nm, 50Nm, 100Nm, 200Nm or 400Nm, maximum rated speed of 1800rpm, with maintain, braking, buffer start, tension control and torque limit. Electric brake has the advantages of quick response, simple structure, no shock vibration and energy saving. Manufacturer direct sales.
2 kW 48V/120V/220V Alternator, 3 Phase
ATO-PMG-2kW
$1,051.53
High efficiency alternator generator in low price, 2 kW best alternator for wind turbine, three phase, rated voltage can choose 48V/96V/120V/220V, it can can significantly extend battery life.
Incremental Rotary Encoder, Hollow Shaft, 4096 ppr
ATO-IRE-4096PH
$269.28
Low priced optical rotary encoder adopts hollow shaft, can sleeve-jointed on motor output shaft, high resolution 4096 ppr, high reliability, high quality, several output modes to choose. 1800 ppr incremental rotaty encoder has optional voltage 5VDC/8-30VDC, optional 6 output modes, Φ80mm shell, Φ25mm shaft and cable edge output connection mode.