2 hp variable frequency drive, 1.5 kW, 1 phase 220V - 240V for single phase AC motor, manufacturer direct sale.
Specification:
| Basics | Model | GK3000-1S0015 |
| Capacity | 2 hp (1.5 kW) | |
| Shipping weight | 2 kg | |
| Dimension | 190*104*150 mm | |
| I/O Feature | Rated current | 9.6 A |
| Input voltage | single phase AC 220V±15% | |
| Input frequency | 47~63Hz | |
| Output voltage | 0~rated input voltage | |
| Output frequency | 0~1000Hz | |
| Over load capacity | 150% of rated current for 60s, 180% of rated current for 10s, 200% of rated current for 3s | |
| Control Features | Control mode | V/F, Sensorless vector control (SVC), Speed sensor vector control (FVC) |
| Operation command mode | Keypad control, Terminal control, Serial communication control | |
| Frequency setting mode | Digital setting, analog setting, pulse frequency setting, serial communication setting, multi-step speed setting & simple PLC, PID setting, etc. These frequency settings can be combined & switched in various modes. | |
| Start frequency | 0.40Hz~20.00Hz | |
| Speed adjustment range | 1:50 | |
| Carrier frequency | 1.0-16.0kHz, automatically adjusted according to temperature and load characteristics | |
| Frequency accuracy | Digital setting: 0.01Hz Analog setting: Maximum frequency * 0.05% | |
| Torque boost | Automatically torque boost; manually torque boost: 0.1%~30.0% | |
| V/f curve | Three types: linear, multiple point and square type (1.2 power, 1.4 power, 1.6 power, 1.8 power, square) | |
| Acceleration/deceleration mode | Straight line/S curve; four kinds of acceleration/deceleration time, range: 0.1s~3600.0s | |
| Jog operation | Jog operation frequency: 0.0Hz~maximum frequency Jog acceleration/deceleration time: 0.1s~3600.0s | |
| Simple PLC & multi-step speed operation | It can realize a maximum of 16 segments speed running via the built-in PLC or control terminal. | |
| Built-in PID | Built-in PID control to easily realize the close loop control of the process parameters (such as pressure, temperature, flow, etc.) | |
| Automatic voltage regulation | Keep output voltage constant automatically when input voltage fluctuating | |
| Control Function | Common DC bus | Common DC bus for several VFDs, energy balanced automatically |
| Torque control | Torque control without PG | |
| Torque limit | "Rooter" characteristics, limit the torque automatically and prevent frequent over-current tripping during the running process | |
| Wobble frequency control | Multiple triangular-wave frequency control, special for textile | |
| Timing/length/counting control | Timing/length/counting control function | |
| Over-voltage & over-current stall control | Limit current & voltage automatically during the running process, prevent frequent over-current & over-voltage tripping | |
| Fault protection function | Up to 30 fault protections including over-current, over-voltage, under-voltage, overheating, default phase, overload, shortcut, etc., can record the detailed running status during failure & has fault automatic reset function | |
| Input/output terminals | Input terminals | Programmable DI: 7 on-off inputs, 1 high-speed pulse input 2 programmable AI: AI1: 0~10V or 0/4~20mA A12: 0~10V or 0/4~20mA |
| Output terminals | 1 programmable open collector output: 1 analog output (open collector output or high-speed pulse output) 2 relay output 2 analog output: 0/4~20mA or 0~10V | |
| Communication terminals | Offer RS485 communication interface, support MODBUS-RTU communication protocol | |
| Human machine interface | LED display | Display frequency setting, output frequency, output voltage, output current, etc. |
| Multifunction key | QUICK/JOG key, can be used as multifunction key | |
| Environment | Ambient temperature | -10℃~40℃, derated 4% when the temperature rise by every 1℃ (40℃~50℃). |
| Humidity | 90%RH or less (non-condensing) | |
| Altitude | ≤1000M: Output rated power, >1000M: Output derated | |
| Storage temperature | -20℃~60℃ |
Note:
- The single phase motor should Not be adjusted to run based on a lower frequency than 80% of its rated frequency for along time, otherwise the motor may fail.
- ATO VFD Cannot be used as a power source, it Can only be directly connected to an induction motor to control the motor speed.
- Single phase VFD Cannot control the motor in reverse, if you want to reverse the motor, refer to the motor nameplate instructions for operation.
- If you have restored the factory settings, please ensure that the phase loss protection has been disabled. PA.13=0.
Details

Tips: Variable frequency drive dust cleaning attentions
In actual operation of the variable frequency drive, the device will always be affected by the environment, such as temperature, humidity, air quality and so on. Especially in the dusty production workshops, if not timely clean up the dust, the operation of the VFD will have a certain impact, or seriously lead to some problems. In the process of dust removal of VFD, there are something need to pay attention:
- Each VFD needs to be dust cleaned once a season.
- Shutdown the VFD before cleaning, and wait for the voltage down to the safety then start working.
- First use brush to clean the dust on the surface of the VFD, but pressure fan is not recommended for the cleaning.
- If the VFD surface is greasy, use a small amount of alcohol to wipe clean, and must wait for the VFD dried before booting again.
- In the maintenance, carefully check whether there are hot discolor parts, whether there is cracking of the cement resistance, or whether the electrolytic capacitors has expansion of leakage hole, protruding holes and other phenomena.
- If possible, remove the shell and use compressed air to blow out the dust inside the VFD and in the wind path. Pay attention when using compressed air because it may contain large amount of moisture. Using a vacuum cleaner is better than compressed air, because the moisture in the compressed air may cause error to the VFD.
Product reviews
High Quality
Redneck
3/20/2019 2:08 AM
This 2hp single phase VFD was bought for my belt grinders. This product is sealed up so that no dust gets inside, which makes it suitable for rugged environment. It's easy to install and no programming requirements. What's more, this unit works well, provides good soft start, and realizes variable speed control. High quality and recommend.
Was this review helpful? (3/0)
Can 2hp VFD be delivered the earliest?
Wass
3/28/2021 7:28 PM
Can you suggest the earliest delivery of 2HP 1-phase VFD?
Was this review helpful? (0/0)
2 hp VFD using current
Robinson
4/29/2021 8:19 PM
Can I use your 2 hp 1 phase drive on a single phase AC 220V-230V blower motor to control the motor speed?
Was this review helpful? (1/0)
2 hp VFD can withstand voltage
Elmer
6/3/2021 11:56 PM
For your GK3000-1S0015 and GK3000-1S0007 1 phase drive, will these take 208v without any issues?
Was this review helpful? (0/0)
Reliable 2hp (1.5kW) VFD
Groove
6/22/2021 9:14 PM
I need adrive for my 2HP motor, why would it not be GK3000-1S0015? Which is listed for 2HP?
Was this review helpful? (0/0)
Can you provide a wire diagram for this application?
Drew
6/27/2022 3:28 AM
I'm installing this VFD on my well pump and using it as a soft start to reduce the impact to my batteries on my solar system. When I wire it in do I still use my Franklin Electric control box with the capacitor or does that get replaced with he VFD? I have a 3 wire 1/2 hp pump, can you provide a wire diagram for this application?
Was this review helpful? (0/0)
How do I set the controller to reverse?
Christopher
1/3/2023 11:45 PM
How can I control the direction of the motor with the control panel rather than installing some switches to the com port? The controller shows a jog/rev button, but it seems to only jog the motor.
Was this review helpful? (0/0)
Well pump controller
Randy
2/11/2023 4:52 PM
I have a Goulds 13GS10412CL submersible pump and I see that it is compatible with variable speed controller. It is 1.0 HP 60 Hz FLA 8.1 SFA 9.4 single phase. What do you recommend as far as VFD to make it constant pressure supply? I would like to use a psi transducer also.
Was this review helpful? (0/0)
Which terminal of VFD will send the signal VFD fault feedback to our PLC?
Rokyd
3/6/2023 1:32 AM
For the GK3000 series, which terminal of VFD will send the signal VFD fault feedback to our PLC? any? So we can disconnect the circuit to VFD, and show the alarm indicator on the our HMI Display
Was this review helpful? (0/0)
The pressure switch on the compressor is normally closed
Alob
3/22/2023 1:32 AM
I have a question about my VFD. The pressure switch on the compressor is normally closed (NC). What happened?
Was this review helpful? (0/0)
2hp
Pedro
5/6/2023 6:04 AM
good morning, I have a 220v 2hp 1440rpm single-phase motor to which I want to install a frequency inverter to control the speed, this inverter; GK3000-1S0015, would it work for me?
Thank you and I await your comments
Thank you and I await your comments
Was this review helpful? (0/0)
A VFD for a drill press
Maisara
5/23/2023 9:48 AM
Hi,
I was wondering if I can use this VFD to drive my drill press 750w permanent split capacitor motor.
I have no idea about how I should connect the motor, my main concern is to control the speed of the motor with keeping the torque. Also, I was wondering if it is possible to control the rotation of the motor and adding external switches and potentiometers. Thank you
I was wondering if I can use this VFD to drive my drill press 750w permanent split capacitor motor.
I have no idea about how I should connect the motor, my main concern is to control the speed of the motor with keeping the torque. Also, I was wondering if it is possible to control the rotation of the motor and adding external switches and potentiometers. Thank you
Was this review helpful? (0/0)
Is there any problem of VFD?
heard
7/20/2023 9:15 PM
2 capacitors are available in the engine start and permanent capacitor is this a problem?
Is there any problem?
Is there any problem?
Was this review helpful? (0/0)
Which VFD input should I connect the winding cable end to?
sita
7/21/2023 1:25 AM
I want to make sure before I buy.
After the engine capacitors are removed, it does not work with the starting load without auxiliary winding, which input should I connect the auxiliary winding cable end to?
After the engine capacitors are removed, it does not work with the starting load without auxiliary winding, which input should I connect the auxiliary winding cable end to?
Was this review helpful? (0/0)
Is there a box available for connecting?
Jakko
8/9/2023 12:16 AM
When installing the VFDs today the electrician said there needs to be a junction box on the VFD where they can connect the conduit for the wires or the VFDs will need to be installed in a cabinet. Is there a box available for connecting conduit that can attach to the VFD or will they need to be installed in a cabinet?
Was this review helpful? (0/0)
Hello
Hesham
10/3/2023 6:19 AM
I want to use this VFD to change frequency of pumps, the nominal current for pumps (two models) are, 6.1 and 8.3 Amps. Which models should I choose?
The pumps rated at 1.1
The pumps rated at 1.1
Was this review helpful? (0/0)
Hello
Mavis
10/16/2023 2:47 AM
Hello,
We are in need of assistance setting up a VFD.
Sequence will be, VFD receives start stop signal and drives to constant speed, no modulating. Need N/O status contacts. Also would like to have dry contact for enabling a relay for a damper.
1) Where do we wire start/stop and how is it programmed?
2) Where do we wire dry contact status? Needs to be N/O and close when fan starts.
3) We would like to have a contact closure to control a damper actuator. Can this be accomplished with Ta, Tb and Tc contacts? When fan starts a contact would close.
We are in need of assistance setting up a VFD.
Sequence will be, VFD receives start stop signal and drives to constant speed, no modulating. Need N/O status contacts. Also would like to have dry contact for enabling a relay for a damper.
1) Where do we wire start/stop and how is it programmed?
2) Where do we wire dry contact status? Needs to be N/O and close when fan starts.
3) We would like to have a contact closure to control a damper actuator. Can this be accomplished with Ta, Tb and Tc contacts? When fan starts a contact would close.
Was this review helpful? (0/0)
I am having issues
joseph
11/23/2023 7:52 PM
I am having issues programming the GK3000 VFD. I am wiring a 240Vac 60hz, 1PH fan motor and I keep getting alarms E-01 and occasionally E-03. What can I adjust to get the frequency drive working?
Was this review helpful? (0/0)
VFD
Andrew
11/23/2023 11:20 PM
Since we are not going to run the fan with full speed power (actually it will only use about 50%), we chose this VFD. Also, the input power supply that I provide is single-phase 220VAC, and we exactly connected the wires as the attached diagram. Also, we could not see any errors when the VFD is running since when we give the power, the lcd panel shows up for few seconds and then fuse blows.
Was this review helpful? (0/0)
The motor cannot spin
Hollis
9/24/2024 12:05 AM
We have purchased a VFD GK3000-1S0015G. I cannot get the Motor to spin. I have connected output power from VFD. I have set output current to10 amps. I cannot set the motor power parameter P8.01 more than 1000. P8.37=0 cannot change. I get an error E-01. I have set: P0.12=100. Torque boost seems to have no affect.
Was this review helpful? (0/0)
GK3000 - Single Phase Pump Install
ULRICH
9/2/2025 1:39 AM
We installed the GK3000 to 1.5kW motor.
The motor runs but gets very hot and trips on E01.
The motor had Start Cap and Run Caps. These have been removed.
Input current will sometimes exceed 14A.
The pump at 50Hz will not get to maximum output.
The motor runs but gets very hot and trips on E01.
The motor had Start Cap and Run Caps. These have been removed.
Input current will sometimes exceed 14A.
The pump at 50Hz will not get to maximum output.
Was this review helpful? (0/0)
Single phase 240 input/ three phase output.
David
11/20/2025 4:14 PM
Is there a guide for setting parameters for supplying a 220 3 phase milling machine with a 2 HP VFD? I am having trouble getting the frequency to go up to 60 HRZ. It comes from the factory with a 50 HRZ setting. Thanks
Was this review helpful? (0/0)
Only registered users can write reviews
Customers who bought this item also bought
1 hp (0.75 kW) VFD, Single Phase Input & Output
GK3000-1S0007
$195.82
Affordable 1 hp VFD, 1 phase for single phase AC induction motor, 220V - 240V 7 amps, manufacturer direct sale.
3 hp (2.2 kW) VFD, Single Phase Input & Output
GK3000-1S0022
$379.23
Cheap 3 hp VFD, 1 phase for single phase AC induction motor, good variable speed performance, 220V - 240V 17 amps, manufacturer direct sale.
3 hp (2.2 kW) AC Line Reactor, 3 Phase Output
ATO-OLR-2d2
$244.54
The 3-phase AC output line reactor material has copper and aluminum for choice, line reactor for vfd. The insulation rank is class F,H, voltage choose from 220V, 380V, 400V, 410V, 440V, 460V or 480V. Low cost, well-made and widely used.
Digital Pressure Sensor for Hydraulic/Steam/Air
ATO-PRES-PX300
$173.33
Digital pressure sensor covers -0.1 to 100 MPa and supports 4–20mA, 0–20mA, voltage and RS485 outputs, with a backlit LCD display. Suitable for hydraulic, steam, air and liquid pressure measurement, with medium temperatures from -40°C to 60°C.
1 hp (750W) 1-phase/3-Phase AC Gear Motor, Ratio 3~100
ATO-GEAR-HV750
$811.69
Good price 3-phase AC gear motor works at 1 hp rated power, gear ratio 3:1~100:1 for selection, torque 1.1~43.2 kg.m, shaft diameter 28mm/32mm, power supply 1-phase/3-phase 110V/220V/380V, horizontal/vertical installation. 750W electric gear motor can operated with a 90V brake to control power cutting.