EMI/RFI Power Line Filter 30A, 3 phase

$108.15
30A EMI/RFI power line filter, 3 phase 3 wire, single stage, rated voltage 250V/440V AC, 50/60Hz, compact size and stud connection, stable performance and low price, best 3-phase EMI filter for the industrial equipment.
SKU: ATO-EMI-1030
Free Shipping
Delivery date: 8-12 days

30A EMI/RFI power line filter is a desired noise filter to protect the 3-phase 3-wire equipment from the outside interference with excellent attenuation performance. It is suitable for 3-phase motor drive, UPS, packaging equipment, textile equipment, industrial air conditioners, and so on.

Specification

ModelATO-MT710-30
Filter TypeEMI
ConfigurationSingle Stage
Rated Current @ 40℃30A
Rated Voltage250V/440V AC
Operating Frequency50/60Hz
PhaseThree Phase Three Wire
Leakage Current≤10mA @ 250V AC 50Hz 20℃
Filter Range150KHz-30MHz
Hipot Rating (one minute)Line to Line1450V DC
Line to Ground2250V DC
Climatic Category25/085/21
Working Temperature-25°C~+85°C
Output TermainalThreaded stud M6
Weight640g
DimensionSee below

Dimensions (Unit: mm)

30A EMI Line Filter Dimension

Electrical Schematic

Three phase emi filter electrical schematic

Insertion Loss Table (in 50Ω system acccording to IEC/CISPR No.17)

6A 10A 20A 30A Power Line Filter Insertion Loss Table

40A 50A 100A EMI Line Filter Insertion Loss Table

Tips: EMI line filter technical parameter - insertion loss

The most important technical parameter of EMI line filter is the capability to restrain interference, normally referring to Insertion Loss. It’s the ratio between the powers transmitting from interference source to load before connecting filter and after connecting filter, and it uses dB as unit. EMI line filter insertion loss is relevant with network parameter of filter network and impedance of source end and load end. To avoid filtering useful signal, insertion loss should be specified carefully. No matter what EMC standard is in the military use or civil use, it has clear specification for equipment or sub system power line conducting interference level. The difference value between estimated or tested EMI conducting interference level and standard conducting interference level is the minimum insertion loss of requested EMI filter. Yet, it is impossible in actual project to do EMC test for different single equipment, then analyze its conducting interference characteristic, and design the filter satisfying with requirement. The suitable power line filter only needs to be selected according to actual status.

Single Phase and Three Phase EMI Power Line Filters

In this video, basic information and installation guidelines for single phase and three phase EMI power line filters are presented.

Product reviews
Good filter and works well.
5
Jerry W
Avatar
10/31/2018 3:28 AM
Good product. Bought one EMI line filter for a trial. I installed for 3D printer to cut down the noise from the power line and it does the job. Works well as expected, and I will buy more.
Was this review helpful? Yes No (0/0)
Power line filter
5
Gabriel
Avatar
4/14/2020 7:25 PM
What is the operating frequency for your power line filter?
Was this review helpful? Yes No (0/0)
ATO Responded
Hi,  Gabriel. The  operating frequency of our filter is  50/60Hz.
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

30A EMI/RFI power line filter is a desired noise filter to protect the 3-phase 3-wire equipment from the outside interference with excellent attenuation performance. It is suitable for 3-phase motor drive, UPS, packaging equipment, textile equipment, industrial air conditioners, and so on.

Specification

ModelATO-MT710-30
Filter TypeEMI
ConfigurationSingle Stage
Rated Current @ 40℃30A
Rated Voltage250V/440V AC
Operating Frequency50/60Hz
PhaseThree Phase Three Wire
Leakage Current≤10mA @ 250V AC 50Hz 20℃
Filter Range150KHz-30MHz
Hipot Rating (one minute)Line to Line1450V DC
Line to Ground2250V DC
Climatic Category25/085/21
Working Temperature-25°C~+85°C
Output TermainalThreaded stud M6
Weight640g
DimensionSee below

Dimensions (Unit: mm)

30A EMI Line Filter Dimension

Electrical Schematic

Three phase emi filter electrical schematic

Insertion Loss Table (in 50Ω system acccording to IEC/CISPR No.17)

6A 10A 20A 30A Power Line Filter Insertion Loss Table

40A 50A 100A EMI Line Filter Insertion Loss Table

Tips: EMI line filter technical parameter - insertion loss

The most important technical parameter of EMI line filter is the capability to restrain interference, normally referring to Insertion Loss. It’s the ratio between the powers transmitting from interference source to load before connecting filter and after connecting filter, and it uses dB as unit. EMI line filter insertion loss is relevant with network parameter of filter network and impedance of source end and load end. To avoid filtering useful signal, insertion loss should be specified carefully. No matter what EMC standard is in the military use or civil use, it has clear specification for equipment or sub system power line conducting interference level. The difference value between estimated or tested EMI conducting interference level and standard conducting interference level is the minimum insertion loss of requested EMI filter. Yet, it is impossible in actual project to do EMC test for different single equipment, then analyze its conducting interference characteristic, and design the filter satisfying with requirement. The suitable power line filter only needs to be selected according to actual status.

Product reviews
Good filter and works well.
5
Jerry W
Avatar
10/31/2018 3:28 AM
Good product. Bought one EMI line filter for a trial. I installed for 3D printer to cut down the noise from the power line and it does the job. Works well as expected, and I will buy more.
Was this review helpful? Yes No (0/0)
Power line filter
5
Gabriel
Avatar
4/14/2020 7:25 PM
What is the operating frequency for your power line filter?
Was this review helpful? Yes No (0/0)
ATO Responded
Hi,  Gabriel. The  operating frequency of our filter is  50/60Hz.
Only registered users can write reviews
Customers who bought this item also bought

30A 3-phase EMI Line Filter, 2 Stage

ATO-EMI-2030
$180.92
3-phase 3-wire dual-stage EMI line filter, 30A rated current, 440V AC rated voltage, light weight and compact design, can effectively protect electrical equipment like packaging machine, servo system from noise interference.