Double Acting Pneumatic Valve Actuator, 145mm Bore Size

$463.29
ATO pneumatic valve actuator for opening and closing butterfly or ball valve, double acting, powered by compressed air, air supply port 1/4 inch, bore size 145mm, air pressure 2.5bar ~ 8bar, aluminum alloy material. Low price, small size, light weight, easy to install and operate.
SKU: ATO-AT-145D
*
Free Shipping
Delivery date: 6-12 days

Pneumatic valve actuator is an executive device that uses air pressure to open and close ball valve, butterfly or regulating valve. The pneumatic actuator powered by compresses air is easy to repair and maintain, and has good adaptability to the environment.

Specifiation

  • Model: ATO-AT145D
  • Bore Size: 145mm (5.7 inch)
  • Air Supply Port: 1/4 inch
  • Power Source: Compressed Air
  • Actuator Type: Double Acting
  • Air Pressure: 2.5bar ~ 8bar
  • Max Working Pressure: 10bar
  • Operating Temperature (Optional): -20℃ ~ 80℃, -35℃ ~ 80℃, -20℃ ~ 150℃
  • Rotation Angle: 90°±5%
  • Body Material: Aluminum Alloy
  • Life Time: One Million Time

Dimensions

Pneumatic actuator dimension

ATO-AT145D

QABCDEFGHI
Φ102/Φ125mm418mm167mm80mm87mm218mm178mm30mm80mmPF
JKOPSTUVWX
M61/4"30mm62mm4mm4mm12mm24mm16mm32mm

Details

Pneumatic valve actuator details

PNNumberNameStandard Material
14Position IndicatorPolypropylene+GF
21Position Indicator SeatPolypropylene+GF
31Snap RingStainless Steel
41BearingStainless Steel
51BearingPolyphthalamide
61Bore BodyExtruded Aluminum alloy
72BearingPolyphthalamide
82PistonDie Cast Aluminum
92O-RingNitrile(NBR70)
102BearingPolyphthalamide
118End Cover bolt gasketStainless Steel
122End Cover boltStainless Steel
132Left and Right end CoverDie Cast Aluminum
142O-RingNitrile(NBR70)
152Guide SleevePolypropylene+GF
161O-RingNitrile(NBR70)
171BearingNylon46
181BearingPolyphthalamide
191Cam SwitchStainless Steel
201Actuating ShaftSteel alloy
211BearingNylon46
221O-RingNitrile(NBR70)
231O-RingNitrile(NBR70)
242Spacer for Limit BoltStainless Steel
252Limit NutStainless Steel
262Limit BoltStainless Steel
27min.5/max.12SpringHigh alloy Spring Steel
281Spring SeatPolypropylene+GF

Tips: Pneumatic valve actuator performance

  1. Under the air pressure of 0.6MPa, the output torque or thrust in the opening and closing directions of the pneumatic device should not be less than the value indicated on the pneumatic device plate, and the action should be flexible, and permanent deformation of each part is not allowed.
  2. When the maximum working pressure is used for the sealing test, the amount of air leaking from the back pressure side is not allowed to exceed (3+0.15D) cm3/min (standard state); The air volume is not allowed to exceed (3+0.15d) cm3/min.
  3. The strength test is carried out with 1.5 times the maximum working pressure. After maintaining the test pressure for 3 minutes, the cylinder end cover and static sealing parts are not allowed to have leakage and structural deformation.
  4. The number of action life times, the pneumatic device simulates the action of the pneumatic valve. Under the condition of maintaining the output torque or thrust capacity in both directions, the opening and closing times of the opening and closing operation should not be less than 50,000 times (the opening-closing cycle is one time).
  5. For the pneumatic device with buffer mechanism, when the piston moves to the end position of the stroke, no impact phenomenon is allowed.

Double Acting Pneumatic Valve Actuator Output Torque Table

Unit: Nm

ModelStandard3bar3.5bar4bar4.5bar5bar5.5bar6bar7bar8bar
ATO-AT032D3.64.355.76.47.388.71011.6
ATO-AT050D8.410.111.713.515.116.718.42023.426.7
ATO-AT063D14.817.720.623.626.529.432.335.3410147
ATO-AT075D29.23540.846.652.558.364.169.981.593.2
ATO-AT088D45.95564.273.382.591.6101.1110.1128.1146.1
ATO-AT100D66.880.193.4106.3120.3133.3146.3160.3183.3213.3
ATO-AT125D139167195223250278303333389444
ATO-AT145D217261304348391434478521608695
ATO-AT160D285341398455512577625682795909
ATO-AT190D53363974685297610651171127714901703
ATO-AT240D893107212501430160817871965214425022859
ATO-AT270D1306156518242084234326032862312136404159

Proposition 65 Warning

*WARNING: This product can expose you to chemicals, including lead, which is known to the State of California to cause birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

Pneumatic valve actuator is an executive device that uses air pressure to open and close ball valve, butterfly or regulating valve. The pneumatic actuator powered by compresses air is easy to repair and maintain, and has good adaptability to the environment.

Specifiation

  • Model: ATO-AT145D
  • Bore Size: 145mm (5.7 inch)
  • Air Supply Port: 1/4 inch
  • Power Source: Compressed Air
  • Actuator Type: Double Acting
  • Air Pressure: 2.5bar ~ 8bar
  • Max Working Pressure: 10bar
  • Operating Temperature (Optional): -20℃ ~ 80℃, -35℃ ~ 80℃, -20℃ ~ 150℃
  • Rotation Angle: 90°±5%
  • Body Material: Aluminum Alloy
  • Life Time: One Million Time

Dimensions

Pneumatic actuator dimension

ATO-AT145D

QABCDEFGHI
Φ102/Φ125mm418mm167mm80mm87mm218mm178mm30mm80mmPF
JKOPSTUVWX
M61/4"30mm62mm4mm4mm12mm24mm16mm32mm

Details

Pneumatic valve actuator details

PNNumberNameStandard Material
14Position IndicatorPolypropylene+GF
21Position Indicator SeatPolypropylene+GF
31Snap RingStainless Steel
41BearingStainless Steel
51BearingPolyphthalamide
61Bore BodyExtruded Aluminum alloy
72BearingPolyphthalamide
82PistonDie Cast Aluminum
92O-RingNitrile(NBR70)
102BearingPolyphthalamide
118End Cover bolt gasketStainless Steel
122End Cover boltStainless Steel
132Left and Right end CoverDie Cast Aluminum
142O-RingNitrile(NBR70)
152Guide SleevePolypropylene+GF
161O-RingNitrile(NBR70)
171BearingNylon46
181BearingPolyphthalamide
191Cam SwitchStainless Steel
201Actuating ShaftSteel alloy
211BearingNylon46
221O-RingNitrile(NBR70)
231O-RingNitrile(NBR70)
242Spacer for Limit BoltStainless Steel
252Limit NutStainless Steel
262Limit BoltStainless Steel
27min.5/max.12SpringHigh alloy Spring Steel
281Spring SeatPolypropylene+GF

Tips: Pneumatic valve actuator performance

  1. Under the air pressure of 0.6MPa, the output torque or thrust in the opening and closing directions of the pneumatic device should not be less than the value indicated on the pneumatic device plate, and the action should be flexible, and permanent deformation of each part is not allowed.
  2. When the maximum working pressure is used for the sealing test, the amount of air leaking from the back pressure side is not allowed to exceed (3+0.15D) cm3/min (standard state); The air volume is not allowed to exceed (3+0.15d) cm3/min.
  3. The strength test is carried out with 1.5 times the maximum working pressure. After maintaining the test pressure for 3 minutes, the cylinder end cover and static sealing parts are not allowed to have leakage and structural deformation.
  4. The number of action life times, the pneumatic device simulates the action of the pneumatic valve. Under the condition of maintaining the output torque or thrust capacity in both directions, the opening and closing times of the opening and closing operation should not be less than 50,000 times (the opening-closing cycle is one time).
  5. For the pneumatic device with buffer mechanism, when the piston moves to the end position of the stroke, no impact phenomenon is allowed.
Only registered users can write reviews