Micro Flow Sensor for Air/Oxygen/Nitrogen, 0~±0.2L/min

$84.92
Micro flow sensor has a flow range of 0 to ±200 sccm (0 to ±0.2 L/min) and an accuracy of ±3% reading, and can be used for air, oxygen and nitrogen flow measurement. Its operating voltage range is 4.75V to 5.25V, and the operating current is 7.5mA to 10mA, which is suitable for many fields such as medical, industrial and laboratory.
SKU: ATO-FS-AFS01
Free Shipping
Delivery date: 6-12 days

The micro gas flow sensor uses the heat transfer principle to measure gas flow. The sensor contains a thermal flow chip and a high-performance CMOS microprocessor with an integrated 24-bit AD set, which has the advantages of high integration and cost performance.

Features

  • The micro flow sensor supports I2C digital communication, which is convenient for integration and data exchange with other devices or systems.
  • The flow sensor is fully calibrated and calibrated at the factory, with high measurement accuracy and good repeatability.
  • It supports bidirectional measurement of forward and reverse flow, which increases the flexibility of application.
  • It has a small hysteresis error and provides real-time, accurate flow data.
  • The sensor is equipped with a convenient installation interface, which simplifies the installation process and reduces the complexity of installation and debugging.

Specification

ModelATO-AFS01
Operating voltage4.75~5.25V
Operating current7.5~10mA
Operating temperature-10~+50℃
Storage temperature-10~70℃
Flow range0~±200sccm (0~±0.2 L/min)
Sampling period0.5s
Accuracy±3% reading
Repeatability±1% reading
Output signalI2C digital signal


Dimension (mm)

Micro flow sensor dimension

Details

Micro flow sensor details

Interface Definition

Micro flow sensor pin

PinNameTypeDescription
1SDAIN/OUTI2C digital communication data pin, built-in 4.7KΩ pull-up resistor
2GND/Ground
3VDD+5VPower supply pin
4SCLINI2C digital communication clock pin, built-in 4.7KΩ pull-up resistor

If the SCL and DATA signal lines are parallel to each other and very close to each other, signal crosstalk and communication failure may occur. The solution is to place a VDD signal or GND between the two signal lines to separate the signal lines. In addition, the integrity of signal transmission can be improved by reducing the SCL frequency. In occasions where the communication environment is more complex, a 100NF decoupling capacitor can be added between the positive and negative pins of the power supply as close to the sensor as possible for filtering.

Micro flow sensor wiring

Installation

When the user's application scenario requires a gas valve for gas control, the gas valve assembly should be installed at the gas input end, and then connected to the sensor to ensure that the product has better air tightness and accuracy. The sensor should be in a fixed installation state in the instrument as much as possible to ensure that the product works in the best condition.

Micro flow sensor installation

Applications

Micro flow sensor applications

Tips: What is this micro flow sensor?

The micro flow sensor is a gas micro flow sensor with high measurement accuracy, good repeatability, long-term stability and full calibration. It uses the heat transfer principle to measure gas flow. The sensor contains a thermal flow chip and a high-performance CMOS microprocessor with an integrated 24-bit AD set. The sensor has the advantages of high integration and cost performance.

The micro flow sensor uses IPC digital communication, and its operating voltage is 5V. The sensor is small in size and suitable for all kinds of scenarios that need to measure gas flow. The micro flow sensor has passed strict factory calibration and outputs the detected flow, reducing the user's use cost and the difficulty of secondary development.

Product reviews
Custom flow sensor
5
Borina
Avatar
1/19/2026 12:25 AM
Hello, I need a miniature flow sensor for air/oxygen/nitrogen, with a flow rate of approximately 5 liters/minute.
Was this review helpful? Yes No (0/0)
ATO Responded
Unfortunately, this flow switch SKU: ATO-FS-AFS01 does not support customization. You can only check the specifications on the website to determine if it can be directly applied to your system.
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

The micro gas flow sensor uses the heat transfer principle to measure gas flow. The sensor contains a thermal flow chip and a high-performance CMOS microprocessor with an integrated 24-bit AD set, which has the advantages of high integration and cost performance.

Features

  • The micro flow sensor supports I2C digital communication, which is convenient for integration and data exchange with other devices or systems.
  • The flow sensor is fully calibrated and calibrated at the factory, with high measurement accuracy and good repeatability.
  • It supports bidirectional measurement of forward and reverse flow, which increases the flexibility of application.
  • It has a small hysteresis error and provides real-time, accurate flow data.
  • The sensor is equipped with a convenient installation interface, which simplifies the installation process and reduces the complexity of installation and debugging.

Specification

ModelATO-AFS01
Operating voltage4.75~5.25V
Operating current7.5~10mA
Operating temperature-10~+50℃
Storage temperature-10~70℃
Flow range0~±200sccm (0~±0.2 L/min)
Sampling period0.5s
Accuracy±3% reading
Repeatability±1% reading
Output signalI2C digital signal


Dimension (mm)

Micro flow sensor dimension

Details

Micro flow sensor details

Interface Definition

Micro flow sensor pin

PinNameTypeDescription
1SDAIN/OUTI2C digital communication data pin, built-in 4.7KΩ pull-up resistor
2GND/Ground
3VDD+5VPower supply pin
4SCLINI2C digital communication clock pin, built-in 4.7KΩ pull-up resistor

If the SCL and DATA signal lines are parallel to each other and very close to each other, signal crosstalk and communication failure may occur. The solution is to place a VDD signal or GND between the two signal lines to separate the signal lines. In addition, the integrity of signal transmission can be improved by reducing the SCL frequency. In occasions where the communication environment is more complex, a 100NF decoupling capacitor can be added between the positive and negative pins of the power supply as close to the sensor as possible for filtering.

Micro flow sensor wiring

Installation

When the user's application scenario requires a gas valve for gas control, the gas valve assembly should be installed at the gas input end, and then connected to the sensor to ensure that the product has better air tightness and accuracy. The sensor should be in a fixed installation state in the instrument as much as possible to ensure that the product works in the best condition.

Micro flow sensor installation

Applications

Micro flow sensor applications

Tips: What is this micro flow sensor?

The micro flow sensor is a gas micro flow sensor with high measurement accuracy, good repeatability, long-term stability and full calibration. It uses the heat transfer principle to measure gas flow. The sensor contains a thermal flow chip and a high-performance CMOS microprocessor with an integrated 24-bit AD set. The sensor has the advantages of high integration and cost performance.

The micro flow sensor uses IPC digital communication, and its operating voltage is 5V. The sensor is small in size and suitable for all kinds of scenarios that need to measure gas flow. The micro flow sensor has passed strict factory calibration and outputs the detected flow, reducing the user's use cost and the difficulty of secondary development.

Product reviews
Custom flow sensor
5
Borina
Avatar
1/19/2026 12:25 AM
Hello, I need a miniature flow sensor for air/oxygen/nitrogen, with a flow rate of approximately 5 liters/minute.
Was this review helpful? Yes No (0/0)
ATO Responded
Unfortunately, this flow switch SKU: ATO-FS-AFS01 does not support customization. You can only check the specifications on the website to determine if it can be directly applied to your system.
Only registered users can write reviews