Capacitance Tank Level Sensor for Oil/Gas Tank, 0-1000mm

$466.00
High performance capacitive level sensor has signal output 4-20mA, 0-5VDC, 0-10VDC, MODBUS, power supply 9 ~ 30VDC, 15 ~ 30VDC, measuring range from 0 to 1000mm. The oil tank level sensor has an IP65 protection rating and can operate in a wide temperature range of -20 to +85℃. ATO capacitive level transmitter can be put in oil tank or gas tank for liquid level measurement.
SKU: ATO-LEVS-1000
*
*
*
*
Free Shipping
Delivery date: 6-12 days

Factory price capacitive tank level sensor is transmitter that use a coaxial container. The capacitor is composed of two coaxial cylindrical plates, an inner electrode and an outer electrode. When the liquid enters the container, the capacitance value between the sensor shell and the sensing electrode will change, and the standard current, voltage or digital signal will be output. It is suitable for measurement of conductive liquids.

Specification

ModelATO-BRW700-2000/ATO-BRW700-204
Measuring Range (Optional)0-300mm, 0-400mm, 0-500mm, 0-600mm, 0-700mm, 0-800mm, 0-900mm, 0-1000mm
Probe Diameterφ16mm
Signal Output (Optional)4-20mA, 0-5VDC, 0-10VDC, MODBUS (RS485/ RS232)
Signal Wire5 Wire, 4 Wire
Thread TypeG1/2
Power Supply9~30VDC, 15~30VDC
Accuracy±0.5%FS (≥600mm), ±1%FS (≥400mm), ±3%FS (≥200mm), ±5%FS (<200mm)
Zero Temperature Drift±0.05 %FS/℃
Working Temperature-20~+85℃
Storage Temperature-40℃~+105℃
Mechanical Vibration±20G
Impact (11ms)100g
Protection GradeIP65
MaterialAluminum Alloy & Stainless Steel
Connection Type (Optional)Direct Wire, M12 Connector


Dimension (Unit: mm)

Dimensions of capacitance liquid level sensor

Connection Type & Wiring

Connection type and wiring of capacitance level sensor

Details

Capacitance level sensor for oil tank detail

Tips: Working principle of capacitance level sensor

Capacitive level sensors use the electrostatic principle. The measurement of such a sensor usually consists of a plate of the capacitor, the outside of the plate is the outer casing of the sensor. This external measurement is usually against the container of the device. When the liquid changes up and down, the internal conductor is covered by the liquid, and the dielectric constant of the capacitor changes, so the capacitance changes, and the state of the circuit connected to the measuring head also changes, so the switch can be controlled to open or close.

According to this principle, when the capacitive liquid level sensor detects that there is water or no water, it can control the power off, or start the water pump switch for automatic water addition. The object detected by this liquid level sensor is not limited to water conductors, but can be oil, nutrient solution, and other liquids.

In this video, ATO will show you top ten most used sensors (sensing technologies).

Product reviews
Awesome capacitance level sensor!
5
Angel
Avatar
4/15/2022 1:25 AM
I really love this capacitance level sensor. Nice, quality replacement with a quick, easy install. It is very accurate and this sensor can use for liquid, oil tank. It is what I want! The quality is great. Highly recommend it!
Was this review helpful? Yes No (0/0)
Need help specify out a level sensor for a sand silo
5
lekah
Avatar
6/7/2023 2:04 AM
Need help specify out a level sensor for a sand silo.
I'm doing a high, med, low, so three sensors was going to use capacity unless you have other suggestions for sensing silica sand reliably.
The sensors will be threaded into a metal silo tank 30mm x 1.5 thread, so the sensor is getting threaded into a metal tank.
Do I need a path to ground? I was looking at some plastic housing sensors with a 2-wire setup, but became concerned about having a path to ground.
Was this review helpful? Yes No (0/0)
ATO Responded
We recommend the Capacitance Level Sensor. This product can meet your needs.
Please feedback on the following information:
1. What liquid do you need to measure? Also, what are the environmental factors like temperature and pressure in the liquid?
2. For the sand silo, what are the high, middle, and low ranges you need to measure? And does the output signal need 4-20mA?
3. Could you please provide a hand-drawn system application for us to refer to the installation position of the sensor for further confirmation?
Sensor Connector
5
Jakos
Avatar
12/2/2025 8:11 PM
Does this sensor, ATO-BRW700-2000/ATO-BRW700-204, come with a 1/2-inch NPT connector when it is 500mm long?
Was this review helpful? Yes No (0/0)
ATO Responded
Sorry, this sensor with a 1/2" NPT connector requires a minimum MOQ of 10 units for customization.
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

Factory price capacitive tank level sensor is transmitter that use a coaxial container. The capacitor is composed of two coaxial cylindrical plates, an inner electrode and an outer electrode. When the liquid enters the container, the capacitance value between the sensor shell and the sensing electrode will change, and the standard current, voltage or digital signal will be output. It is suitable for measurement of conductive liquids.

Specification

ModelATO-BRW700-2000/ATO-BRW700-204
Measuring Range (Optional)0-300mm, 0-400mm, 0-500mm, 0-600mm, 0-700mm, 0-800mm, 0-900mm, 0-1000mm
Probe Diameterφ16mm
Signal Output (Optional)4-20mA, 0-5VDC, 0-10VDC, MODBUS (RS485/ RS232)
Signal Wire5 Wire, 4 Wire
Thread TypeG1/2
Power Supply9~30VDC, 15~30VDC
Accuracy±0.5%FS (≥600mm), ±1%FS (≥400mm), ±3%FS (≥200mm), ±5%FS (<200mm)
Zero Temperature Drift±0.05 %FS/℃
Working Temperature-20~+85℃
Storage Temperature-40℃~+105℃
Mechanical Vibration±20G
Impact (11ms)100g
Protection GradeIP65
MaterialAluminum Alloy & Stainless Steel
Connection Type (Optional)Direct Wire, M12 Connector


Dimension (Unit: mm)

Dimensions of capacitance liquid level sensor

Connection Type & Wiring

Connection type and wiring of capacitance level sensor

Details

Capacitance level sensor for oil tank detail

Tips: Working principle of capacitance level sensor

Capacitive level sensors use the electrostatic principle. The measurement of such a sensor usually consists of a plate of the capacitor, the outside of the plate is the outer casing of the sensor. This external measurement is usually against the container of the device. When the liquid changes up and down, the internal conductor is covered by the liquid, and the dielectric constant of the capacitor changes, so the capacitance changes, and the state of the circuit connected to the measuring head also changes, so the switch can be controlled to open or close.

According to this principle, when the capacitive liquid level sensor detects that there is water or no water, it can control the power off, or start the water pump switch for automatic water addition. The object detected by this liquid level sensor is not limited to water conductors, but can be oil, nutrient solution, and other liquids.

Product reviews
Awesome capacitance level sensor!
5
Angel
Avatar
4/15/2022 1:25 AM
I really love this capacitance level sensor. Nice, quality replacement with a quick, easy install. It is very accurate and this sensor can use for liquid, oil tank. It is what I want! The quality is great. Highly recommend it!
Was this review helpful? Yes No (0/0)
Need help specify out a level sensor for a sand silo
5
lekah
Avatar
6/7/2023 2:04 AM
Need help specify out a level sensor for a sand silo.
I'm doing a high, med, low, so three sensors was going to use capacity unless you have other suggestions for sensing silica sand reliably.
The sensors will be threaded into a metal silo tank 30mm x 1.5 thread, so the sensor is getting threaded into a metal tank.
Do I need a path to ground? I was looking at some plastic housing sensors with a 2-wire setup, but became concerned about having a path to ground.
Was this review helpful? Yes No (0/0)
ATO Responded
We recommend the Capacitance Level Sensor. This product can meet your needs.
Please feedback on the following information:
1. What liquid do you need to measure? Also, what are the environmental factors like temperature and pressure in the liquid?
2. For the sand silo, what are the high, middle, and low ranges you need to measure? And does the output signal need 4-20mA?
3. Could you please provide a hand-drawn system application for us to refer to the installation position of the sensor for further confirmation?
Sensor Connector
5
Jakos
Avatar
12/2/2025 8:11 PM
Does this sensor, ATO-BRW700-2000/ATO-BRW700-204, come with a 1/2-inch NPT connector when it is 500mm long?
Was this review helpful? Yes No (0/0)
ATO Responded
Sorry, this sensor with a 1/2" NPT connector requires a minimum MOQ of 10 units for customization.
Only registered users can write reviews