30mm Miniature Electrical Slip Ring, 4-Wire 30A, 2-Wire 50A

$99.89
Miniature electrical slip ring can 360° rotate transmit large current and. It is capsule design, outer diameter is 30mm. Standard circuits can select 4 wires 30A or 2 wires 50A large current, customized specifications are available. Rotation speed is 250rpm. With A-type flange, installation and use of slip rings are easy.
SKU: ATO-MNTSR-300
*
Free Shipping
Delivery date: 6-12 days

Miniature electrical slip ring core process is a gold-gold contact point with high stability and longevity. Wires of the miniature slip ring rotor and stator use multi-color colored wires, and the wiring is simple. It is widely used in consumer electronics, small wind turbines, stage lights, etc. It can also be used in induction cookers, dining tables and other equipment that require large current and small size of the slip ring.

Specification

ModelATO-M300A
Outer Diameter30mm
Rotating Speed250 rpm
Working Temp.-30℃~80℃
Working Humidity0~85% RH
Contact Materialgold-gold
Housing Materialplastic
Torque0.05N.m (+0.01N.m/6 circuits)
Working Life10 millions for ref (depends on working conditions)
Rated Voltage0~440VAC/VDC
Lnsulation Resistance≥300MΩ/300VDC
Lead Wire Spec.refer to model list
Lead Wire Lengthstandard 200mm (can be customized)
CertificationCE, RoHS
Dielectric Strength300VAC@50Hz,60s
Electrical Noise<0.01Ω
IP GradeIP51

30mm Miniature Electrical Slip Ring (Type A Flange) Dimension Drawing

30mm Miniature Electrical Slip Ring (Type A Flange) Dimension Drawing

Standard Model List

ModelNumber of Circuit WiresMax current/wireLead spec.Length L (mm)
ATO-M300A-0430430AAWG12#teflon, silver plated50
ATO-M300A-0250250AAWG12*2#teflon, silver plated50
ATO-M300A-0630630AAWG12#teflon, silver plated65.7

Color Code of Lead Wire

ring #123456
colorBLKBRNREDORGYELGRN

Miniature Slip Ring Connector Installation Diagram

Miniature Slip Ring Connector Installation Diagram

Tips: Faults and solutions in the use of miniature slip rings

  1. Short circuiting of the miniature slip ring after a period of use is possible due to the slip ring life. Another reason is that the slip ring is overloaded, causing the slip ring to burn out. In general, the short circuit of a new slip ring is caused by the problem of inner insulating material of the slip ring or direct short circuit between brush wire and brush wire, the wire is broken. This fault must be detected by the exclusion method.
  2. Signal interference of the miniature slip ring is too large. Slip rings can be used to transmit power and signals, and interference can occur between power supply and signal. The interference is divided into internal interference and external interference. Users must clearly know the type of signal during use. For special signals, use special wires to shield internal and external. For the slip ring that has been formed, when it is found that the slip ring signal is disturbed, users can shield the external wire by self.
  3. Miniature slip ring does not rotate smoothly. Excluding the problem of slip ring assembly and bearing selection, the cause of such problems is usually that the user does not propose shockproof requirements when selecting the slip ring. If the working environment has strong vibration, it will cause damage to the thin-walled bearings and cracking of the plastic spindle in the slip ring.
  4. IP grade of the miniature slip ring does not match the working environment. Normally, the slip ring IP grade is IP51. Some users put slip ring in the place with waterproof requirements without additional protection, causing water inside the slip ring to cause internal short circuit and causing the slip ring to fail.
  5. Miniature slip ring overload causes burnout. The allowed maximum current of the slip ring is the safely operable current value calculated based on the cross-sectional area, brush contact area, pressure of the brush and the contact surface, and rotational speed. If the current exceeds this value, the slip ring will be hot, or the contact surface will be ignited, even forming a solder joint between the brush and the slip ring. Although the slip ring will consider a certain safety factor during the production design phase, it is recommended that users provide the maximum current of actual application to slip ring manufacturers.

Proposition 65 Warning

*WARNING: This product can expose you to chemicals, including lead, which is known to the State of California to cause birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Product reviews
Excellent slip ring
5
Adrian
Avatar
5/30/2022 12:22 AM
The electrical slip ring is well made, frictionless, and comes with thick quality wire. However, there is really no way to look inside and see if it really is a gold swivel or how durable the internal connectors are. Time will tell if this is a good choice.
I really like the accuracy of this clamp meter, and I compared it to several clamp meters I have and it measured very accurately. I will use it more and see how reliable it is, time will tell.
Was this review helpful? Yes No (0/0)
Custom slip ring
5
Nikolai
Avatar
9/24/2026 12:12 AM
Hello, I am looking for a custom rotary joint and slip ring combination product that supports two fluid lines (medium: water), four 4 AWG power lines, and at least six signal lines.
Was this review helpful? Yes No (0/0)
ATO Responded
Hello. We also need to know: what is the specific current (in amperes) for the four power lines? What size tubing is required? This will allow us to provide a better recommendation.
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

Miniature electrical slip ring core process is a gold-gold contact point with high stability and longevity. Wires of the miniature slip ring rotor and stator use multi-color colored wires, and the wiring is simple. It is widely used in consumer electronics, small wind turbines, stage lights, etc. It can also be used in induction cookers, dining tables and other equipment that require large current and small size of the slip ring.

Specification

ModelATO-M300A
Outer Diameter30mm
Rotating Speed250 rpm
Working Temp.-30℃~80℃
Working Humidity0~85% RH
Contact Materialgold-gold
Housing Materialplastic
Torque0.05N.m (+0.01N.m/6 circuits)
Working Life10 millions for ref (depends on working conditions)
Rated Voltage0~440VAC/VDC
Lnsulation Resistance≥300MΩ/300VDC
Lead Wire Spec.refer to model list
Lead Wire Lengthstandard 200mm (can be customized)
CertificationCE, RoHS
Dielectric Strength300VAC@50Hz,60s
Electrical Noise<0.01Ω
IP GradeIP51

30mm Miniature Electrical Slip Ring (Type A Flange) Dimension Drawing

30mm Miniature Electrical Slip Ring (Type A Flange) Dimension Drawing

Standard Model List

ModelNumber of Circuit WiresMax current/wireLead spec.Length L (mm)
ATO-M300A-0430430AAWG12#teflon, silver plated50
ATO-M300A-0250250AAWG12*2#teflon, silver plated50
ATO-M300A-0630630AAWG12#teflon, silver plated65.7

Color Code of Lead Wire

ring #123456
colorBLKBRNREDORGYELGRN

Miniature Slip Ring Connector Installation Diagram

Miniature Slip Ring Connector Installation Diagram

Tips: Faults and solutions in the use of miniature slip rings

  1. Short circuiting of the miniature slip ring after a period of use is possible due to the slip ring life. Another reason is that the slip ring is overloaded, causing the slip ring to burn out. In general, the short circuit of a new slip ring is caused by the problem of inner insulating material of the slip ring or direct short circuit between brush wire and brush wire, the wire is broken. This fault must be detected by the exclusion method.
  2. Signal interference of the miniature slip ring is too large. Slip rings can be used to transmit power and signals, and interference can occur between power supply and signal. The interference is divided into internal interference and external interference. Users must clearly know the type of signal during use. For special signals, use special wires to shield internal and external. For the slip ring that has been formed, when it is found that the slip ring signal is disturbed, users can shield the external wire by self.
  3. Miniature slip ring does not rotate smoothly. Excluding the problem of slip ring assembly and bearing selection, the cause of such problems is usually that the user does not propose shockproof requirements when selecting the slip ring. If the working environment has strong vibration, it will cause damage to the thin-walled bearings and cracking of the plastic spindle in the slip ring.
  4. IP grade of the miniature slip ring does not match the working environment. Normally, the slip ring IP grade is IP51. Some users put slip ring in the place with waterproof requirements without additional protection, causing water inside the slip ring to cause internal short circuit and causing the slip ring to fail.
  5. Miniature slip ring overload causes burnout. The allowed maximum current of the slip ring is the safely operable current value calculated based on the cross-sectional area, brush contact area, pressure of the brush and the contact surface, and rotational speed. If the current exceeds this value, the slip ring will be hot, or the contact surface will be ignited, even forming a solder joint between the brush and the slip ring. Although the slip ring will consider a certain safety factor during the production design phase, it is recommended that users provide the maximum current of actual application to slip ring manufacturers.

Product reviews
Excellent slip ring
5
Adrian
Avatar
5/30/2022 12:22 AM
The electrical slip ring is well made, frictionless, and comes with thick quality wire. However, there is really no way to look inside and see if it really is a gold swivel or how durable the internal connectors are. Time will tell if this is a good choice.
I really like the accuracy of this clamp meter, and I compared it to several clamp meters I have and it measured very accurately. I will use it more and see how reliable it is, time will tell.
Was this review helpful? Yes No (0/0)
Custom slip ring
5
Nikolai
Avatar
9/24/2026 12:12 AM
Hello, I am looking for a custom rotary joint and slip ring combination product that supports two fluid lines (medium: water), four 4 AWG power lines, and at least six signal lines.
Was this review helpful? Yes No (0/0)
ATO Responded
Hello. We also need to know: what is the specific current (in amperes) for the four power lines? What size tubing is required? This will allow us to provide a better recommendation.
Only registered users can write reviews