The energy-saving and efficient dual-channel RS485 to analog signal converter is a must-have tool for industrial control, providing a wide range of 4-20mA, 0-5V, and 0-10V signal outputs with high compatibility to meet different system requirements. The converter is based on ModBus-RTU protocol for stable and reliable communication and supports address range 1-254 with flexible baud rate adjustment. 12-bit AD conversion resolution and ±0.1%FS typical accuracy ensure highly accurate signal output.
Specification
| Model | ATO-SN-3001-I20-2 | ATO-SN-3001-V05-2 | ATO-SN-3001-V10-2 |
| Output Signal | 4~20mA | 0~5V | 0~10V |
| DC Power Supply | 5-30V | ||
| Maximum Power Consumption | 0.08W (DC12V) | ||
| Operating Temperature | -40℃~+60℃ | ||
| AD Conversion Resolution | 12 bits | ||
| Accuracy | Typical accuracy: -0.1%FS | ||
| Communication Interface | ModBus-RTU | ||
| Address Range | 1-254(default 1) | ||
| Baud Rate | Numeric range: 0-7 | ||
| 0: 2400bps | |||
| 1: 4800bps | |||
| 2: 9600bps | |||
| 3: 19200bps | |||
| 4: 38400bps | |||
| 5: 57600bps | |||
| 6: 115200bps | |||
| 7: 1200bps | |||
| Default: 4800bps | |||
| Output Impedance | 4-20mA: ≤200Ω | ||
| 0-5V: ≥10kΩ | |||
| Dimension | 88mm*φ2.5mm | ||
| Net Weight | 350g | ||
Features
- Supports 2 analog outputs of current type and voltage type, each output type is selectable.
- 12-bit resolution, 0.1% accuracy.
- ADC supports standard ModBus-RTU communication protocol.
- With lightning, static protection RS485 communication interface, op amp signal isolation address, baud rate can be set through the host computer software.
- With anti-reverse connection, over-voltage protection, over-current protection, short circuit protection.
Dimensional Drawing (unit: mm)

Wiring Drawing

Note: The circuit board needs to be modified accordingly.
- If current input is selected, short the left and center pins of the shorting cap corresponding to the number of circuits.
- If voltage input is selected, short the right and center pins of the corresponding shorting cap. I and V are indicated on the circuit board.
Applications

Tips: Why is there a problem of unstable output signal?
The unstable output signal is usually caused by the following reasons:
- Power supply problem: Check whether the power supply voltage is stable and meets the converter requirements.
- Wiring problem: Make sure the RS485 communication and analog output are wired correctly to avoid short circuit or poor contact.
- Communication interference: RS485 line may be subject to electromagnetic interference, need to use shielded wire and proper grounding.
- Configuration error: Check whether the software configuration matches the actual demand.
- If the problem persists, it is recommended to contact the manufacturer's technical support for further assistance.
Product reviews
A stable RS485 converter
Lucian
9/8/2025 12:29 AM
I have used converters of other brands before, but they often had signal drift problems. This ATO product has significantly better stability. The signal remains accurate even after long-term operation, especially in harsh environments. The anti-static and lightning protection designs are very practical.
Was this review helpful? (0/0)
Stable converter, easy setup
Ian
9/1/2026 1:25 AM
Used this converter to connect a digital sensor to an older control system. Setup was straightforward, and the Modbus communication worked as expected. The two-channel output is convenient and saves some space in the control cabinet. So far, the signal has been stable during continuous operation.
Was this review helpful? (0/0)
Only registered users can write reviews
Customers who bought this item also bought
Digital Rotary Torque Sensor, 0.1/5/300/1000 Nm to 10000 Nm
ATO-TQS-D03
$939.15
Digital rotary torque sensor with LCD display has the capacity range from 0.1 Nm/0.3 Nm/1 Nm/5 Nm/10 Nm/300 Nm/1000 Nm to 10000 Nm. LCD display can show torque, speed and power value at the same time. Dynamic torque sensor adopts two NSK shafts to ensure starting torque as low as 0.00001 Nm. Rotary torque transducer with 7 pin waterproof circular connector and 3m cable can measure both forward and reverse torque, and then output ±5V/0-10V/4-20mA/RS485 torque signal to PLC.
Manual Tension Controller for Magnetic Powder Clutch/Brake
ATO-TC-001
$101.98
Compact manual tension controller with an output voltage of 24V DC, providing current for excitation powder clutch/brake, hysteresis clutch/brake, etc. Manual tension controller is suitable for slitting machines, printing machines, and other equipment requiring channel tension control or cable processing.
RS485 to 4-20mA/0-5V/0-10V Converter, 4 Channel
ATO-RT-4-Channel
$85.55
This favorable price RS485 converter is a high-performance, multi-functional, industrial-grade device that supports 4-20mA, 05V and 0~10V output signals, and the 4-channel outputs are specifically designed for accurate conversion of RS485 signals to analog signals.