This micro laser displacement sensor uses a laser beam to measure the distance between the object and the sensor. 12...24V DC supply voltage, repeat accuracy up to 800μm, 50m/100m/400m measurement center distance, and 4-20mA or 0-5V output signal are available.
Specifications
| Model | ATO-PDE-CR50TGIU | ATO-PDE-CR100TGIU | ATO-PDE-CR400TGIU |
| Type | Analog Quantity + Switch Quantity | ||
| Measurement Center Distance | 50mm | 100mm | 400mm |
| Measurement Range | ±15mm | ±35mm | ±200mm |
| Full Scale (F.S.) | 35-65mm | 65-135mm | 200-600mm |
| Power Supply Voltage | 12...24V DC | ||
| Power Consumption | ≤960mW | ||
| Load Current | 100mA | ||
| Voltage Drop | <2V | ||
| Light Source Type | Red Laser (658±8nm); Laser Class: Class 2; Maximum Average Power: 1mW; Pulse Width: 450μs; Beam Angle: 0.06°; Frequency: 1.67kHz | ||
| Beam Diameter | About Φ70μm (at 50mm) | About Φ120μm (at 100mm) | About Φ500μm (at 400mm) |
| Resolution | 10μm | 100μm | |
| Linear Accuracy② | ±0.1%F.S. | ±0.2%F.S. (Measurement Distance 200mm-400mm); ±0.3%F.S. (Measurement Distance 400mm-600mm) | |
| Repeat Accuracy② | 30μm | 70μm | 300μm@200mm-400mm; 800μm@400mm (Inclusive)-600mm |
| Output | Analog Quantity: 4-20mA (Load Resistance<300Ω)/0-5V (Load Resistance>5kΩ); Switch Quantity: NPN/PNP and NO/NC can be set. | ||
| Distance Setting | Button Setting | ||
| Response Time | <10ms | ||
| Dimensions | 45mmx27mmx21mm | ||
| Display | OLED Display (Size: 18x10mm) | ||
| Temperature Drift | <0.03%F.S./℃ | <0.04%F.S./℃ | |
| Indicator Light | Laser Working Indication: Green Light; Switch Output Indication: Yellow Light | ||
| Protection Circuit | Short Circuit Protection, Reverse Polarity Protection, Overload Protection | ||
| Built-In Function | Teaching Mode, Reference Value Fine-Tuning; Peak And Valley Value Retention; Zero Setting; Key Lock; Factory Reset; Chinese and English Switching; Energy Saving Mode, etc. | ||
| Use Environment | Working Temperature: -10...+45℃; Storage Temperature: -20...+60℃; Ambient Humidity: 35...85%RH (No Condensation) | ||
| Ambient Light Resistance | Incandescent Lamp: ≤3,000 lux; Sunlight Interference: ≤10,000 lux | ||
| Protection Level | IP65 | ||
| Material | Casing: Zinc Alloy; Lens: Glass; Display: Glass | ||
| Vibration Resistance | 10. ..55Hz, Double Amplitude 1.5mm, 0.5 Hours in Each of the Three Directions of X, Y, and Z | ||
| Impact Resistance | 500m/s2 (about 50G), 3 Times in each of the Three Directions of X, Y, and Z | ||
| Connection Method | 2m Composite Cable (0.2mm2) | ||
Dimensions (Unit: mm)

Wiring

Tips for Using Laser Displacement Sensor
- The maximum allowable power supply voltage of this laser displacement sensor is 10% of the rated voltage. Please confirm that the power supply voltage is less than the maximum allowable value before powering on.
- It takes a certain amount of time for the sensor to be initialized from power on to normal detection. Please make sure that it is used for more than the initialization time after powering on.
- When the sensor and the load use different power supplies, please make sure to turn on the power supply of the sensor first.
- When the sensor is not in use, it is recommended to cut off the power supply to the load first, and then cut off the power supply to the sensor.
- When installing the laser displacement sensor, do not subject the sensor to severe external force (such as hammering, etc.), which may damage the sensor's performance.
- Avoid using thinners, alcohol, or other organic solvents when cleaning.
Product reviews
Reliable laser sensor
Arthur
5/18/2026 6:54 PM
We use the 400mm version for tank level monitoring. The 4‑20mA output is linear and repeatable. Easy to install with the OLED display for setup. IP65 holds up in dusty areas. Very reliable.
Was this review helpful?
(0/0)
Only registered users can write reviews