Hot Runner Temperature Controller

$216.35
Hot runner temperature controller is specially used to detect the temperature of hot runner system. By adjusting the output power, the target temperature value of hot runner system can be kept stable. The hot runner temperature controller adopts an adaptive control method combining fuzzy control and PID control, and the temperature control accuracy can reach 1℃. The input thermocouple type is J type or K type. The temperature settnig range is 0~450℃ (32~842℉).
SKU: ATO-TEMPC-HR
Free Shipping
Delivery date: 6-12 days

Hot runner temperature controller special for hot runner system temperature control, with fuzzy control and PID control mode, input thermocouple J type or K type.

Specification:

ModelATO-TEMPC-S201
Shipping weight1kg
Size50*200*200mm
Power supply85-245VAC, 50/60Hz
Load capacity15A (50W-1650W, 110V) / (100W-3600W, 240V)
Output typePWM (Pulse Width Modulation)
Display4 digit LED dual digital display for PV and SV
Temperature sensor typeThermocouple J type or K type
Temperature setting range0~450℃ (32~842℉)
Temperature accuracy0.5%FS
Temperature control modeFuzzy+PID
Function1. Self-adaption temperature control
2. Automatic environment linear temperature compensation
3. Thermocouple open circuit/reverse/short circuit protection
4. Heater open circuit/short circuit protection
5. Insurance tube open circuit alarm
6. Heater output current monitoring
7. Output percentage view
8. Temperature deviation alarm
9. Leakage error detection
10. Manual output power mode
11. Soft start locking
Environment temperature-10~+55℃ (14~131℉)
Environment humidity10-80% (No condensation)
Warranty2 years

Wiring diagram:
Hot runner temperature controller wiring diagram
Tips: What is the soft start effect in hot runner temperature controller?
First, the temperature rise of the hot runner temperature controller must conform to the laws of heat conduction and heat distribution, and a good temperature rise curve is required. It is not the faster the temperature rises, the better the temperature control. Too fast heating not only won't improve production efficiency but also will cause damage to the hot runner and related parts.
If the hot runner is not the first time to use, there is residuum in it. If the temperature rises fast,  the residual plastic will be heated first. And the heating of the entire flow channel will be very uneven, which will cause the plastic remaining in the runner near the heating circle to be scorched and the plastic that was injected far from the heating circle could not be melted. Therefore, the soft start is a necessary preheating process, it will avoid product failure, avoid plastic harden or even carbonize on the inner wall of the hot runner and adhere to it, and avoid hot runner blocking over time and reduce the service life.

Product reviews
High quality temperature controller
5
Mclendon
Avatar
8/23/2021 1:42 AM
Do you provide 4 wire PID temperature controllers to be used with my 4 wire PT100?
Was this review helpful? Yes No (0/0)
ATO Responded
Do not provide 4 wire PID temperature controller but our 3 wire PID can be connected/worked with the 4 wire PT100 without any issue!
Request – Compatible XMTL-760S Temperature Controller
5
RAUL
Avatar
7/23/2025 2:30 PM
Hello,

I am interested in buying a Hot Runner Temperature Controller with the following specifications:

Model required: Similar or equivalent to XMTL-760S

Temperature range: 0–600 °C

Input type: Thermocouple K (J optional is fine)

Output: Mechanical relay (NO contact), not SSR

Power supply: 220 V AC

Single zone

Same wiring as the attached photo (see wiring diagram for terminals 1–7)

Please confirm if you have this model or compatible one, and send me the price including shipping to Zapopan, Jalisco, Mexico (CP 45019).

I’ve attached a photo of the exact module we currently use for comparison.

Thank you!
Was this review helpful? Yes No (0/0)
ATO Responded
Please contact our business email at sales@ato.com or service@ato.com and they will give you recommendations or quotes.
Write your review
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*
*

Hot runner temperature controller special for hot runner system temperature control, with fuzzy control and PID control mode, input thermocouple J type or K type.

Specification:

ModelATO-TEMPC-S201
Shipping weight1kg
Size50*200*200mm
Power supply85-245VAC, 50/60Hz
Load capacity15A (50W-1650W, 110V) / (100W-3600W, 240V)
Output typePWM (Pulse Width Modulation)
Display4 digit LED dual digital display for PV and SV
Temperature sensor typeThermocouple J type or K type
Temperature setting range0~450℃ (32~842℉)
Temperature accuracy0.5%FS
Temperature control modeFuzzy+PID
Function1. Self-adaption temperature control
2. Automatic environment linear temperature compensation
3. Thermocouple open circuit/reverse/short circuit protection
4. Heater open circuit/short circuit protection
5. Insurance tube open circuit alarm
6. Heater output current monitoring
7. Output percentage view
8. Temperature deviation alarm
9. Leakage error detection
10. Manual output power mode
11. Soft start locking
Environment temperature-10~+55℃ (14~131℉)
Environment humidity10-80% (No condensation)
Warranty2 years

Wiring diagram:
Hot runner temperature controller wiring diagram
Tips: What is the soft start effect in hot runner temperature controller?
First, the temperature rise of the hot runner temperature controller must conform to the laws of heat conduction and heat distribution, and a good temperature rise curve is required. It is not the faster the temperature rises, the better the temperature control. Too fast heating not only won't improve production efficiency but also will cause damage to the hot runner and related parts.
If the hot runner is not the first time to use, there is residuum in it. If the temperature rises fast,  the residual plastic will be heated first. And the heating of the entire flow channel will be very uneven, which will cause the plastic remaining in the runner near the heating circle to be scorched and the plastic that was injected far from the heating circle could not be melted. Therefore, the soft start is a necessary preheating process, it will avoid product failure, avoid plastic harden or even carbonize on the inner wall of the hot runner and adhere to it, and avoid hot runner blocking over time and reduce the service life.

Product reviews
High quality temperature controller
5
Mclendon
Avatar
8/23/2021 1:42 AM
Do you provide 4 wire PID temperature controllers to be used with my 4 wire PT100?
Was this review helpful? Yes No (0/0)
ATO Responded
Do not provide 4 wire PID temperature controller but our 3 wire PID can be connected/worked with the 4 wire PT100 without any issue!
Request – Compatible XMTL-760S Temperature Controller
5
RAUL
Avatar
7/23/2025 2:30 PM
Hello,

I am interested in buying a Hot Runner Temperature Controller with the following specifications:

Model required: Similar or equivalent to XMTL-760S

Temperature range: 0–600 °C

Input type: Thermocouple K (J optional is fine)

Output: Mechanical relay (NO contact), not SSR

Power supply: 220 V AC

Single zone

Same wiring as the attached photo (see wiring diagram for terminals 1–7)

Please confirm if you have this model or compatible one, and send me the price including shipping to Zapopan, Jalisco, Mexico (CP 45019).

I’ve attached a photo of the exact module we currently use for comparison.

Thank you!
Was this review helpful? Yes No (0/0)
ATO Responded
Please contact our business email at sales@ato.com or service@ato.com and they will give you recommendations or quotes.
Only registered users can write reviews