To clarify i am suggesting to use this 600W water well pump as a complete package (and run everything from 220V single phase inout to the DC converter/controller).
The lift heigh would be 2M, and flow rate equivalent to below which is the current pump, and I wish to replace with one that has a variable control and also is not at mains voltage for safety reasons.
600 watt submersible well pump adopts stainless steel impeller and has 48V working voltage, 1004~1585 gph max. flow, 42~80m max. head. 3 inch water well pump with an external DC controller is used for ponds, farms, fountains or pools.
Well Pump Features
| Model | ATO-3DPC3.8-80-48-600 | ATO-3DSC4.5-80-48-600 | ATO-4DPC6-42-48-600 |
| Max. flow | 3.8m3/h (1004 gph, American system) | 4.5m3/h (1189 gph, American system) | 6.0m3/h (1585 gph, American system) |
| Max. head | 80m (260ft) | 80m (260ft) | 42m (135ft) |
| Length | 60cm | 70cm | 50cm |
| Inlet diameter | 3 inch | 3 inch | 4 inch |
| Outlet diameter | 1.25 inch | 1.25 inch | 1.25 inch |
| Structure | Single-suction plastic impeller | Single-suction stainless steel impeller | Single-suction plastic impeller |
| Material of outlet/connector/oil cylinder | Brass | Stainless steel | Brass |
| Power | 600W | ||
| Voltage | 48V DC | ||
| Internal motor | Brushless DC motor | ||
| Speed | 4000rpm | ||
| Material of shaft | 304 stainless steel | ||
| No water protection function | The water pump stops working automatically when there is no water in the well, and it will automatically restart working 30 minutes later. | ||
| Required open circuit voltage (VOC) of solar panel | <120V DC | ||
| Required power of solar panel | ≥1.3*pump power | ||
| Efficiency | 45% | ||
| Warranty | 2 years | ||
| Cable length | 2m | ||
Controller Features
| Model | DF-48 |
| Best MPPT voltage range | 60-90V DC |
| Max. input current | 17A |
| Working temperature | -15~+60℃ (5~140℉) |
| Display | LED display can show power, voltage, current and speed value. |
| Functions | Automatic charging (for battery) Variable frequency Automatic power ON/OFF Soft start High voltage/low voltage/over-current/high temperature protection |
| Protection class | IP65 |
Package included
- 1 * Water well pump with 2m cable
- 1 * DC controller
- 1 * Stainless steel float switch (water level sensor for the tank)
- 1 * Pump outlet joint connector
- 1 * Splice kit for cable join
- 1 * Splice kit for waterproof
- 1 * User manual
600W water well pump performance curves
Max. Flow: 3.8m3/h, Max. Head: 80m, Model: 3DPC3.8-80-48-600

Max. Flow: 4.5m3/h, Max. Head: 80m, Model: 3DSC4.5-80-48-600

Max. Flow: 6.0m3/h, Max. Head: 42m, Model: 4DPC6-42-48-600

Tips: Protection functions of water well pump and DC controller
- Over-current protection: When the water well pump model is mismatched or UVW three-phase in short-circuit connection.
- Phase protection: UVW three-phase is in an open circuit.
- Stall protection: When the pump model is mismatched. A pump extension cord is too long. Solar water pump power is too low. The pump bearing is stuck.
- Low voltage protection: The input voltage of the solar pump is too low.
- High voltage protection: The input voltage is too high.
- Dry-run protection: Not all of the air in the pump is exhausted. There is no water in the deep well/pond.
- High-temperature protection: The temperature of the DC controller MCU is more than 90℃.
- Reverse connection protection: The wiring is wrong.
Customers who bought this item also bought
300W Submersible/Deep Water Well Pump, 24V DC
ATO-SWP-24V300
$727.27
300W water well pump adopts stainless steel impeller and has maximum head 35m (115ft), maximum flow 3.5m3/h, DC 24 volt working voltage, 3 inch inlet diameter and 1.25 inch outlet diameter. Deep well pump with special DC controller supplies for pool, tank, water feature or fountain.